584,861 active members*
4,767 visitors online*
Register for free
Login

Search:

Type: Posts; User: oldgoat

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    2,305

    Re: Full radius program

    Check your geometry first. I do not recall what the error limit maximum is (usually parameter??), but your numbers do not add up.

    .630 minor groove diameter + .120 radius = .870 diameter + .03...
  2. Thread: 11M 4TH Axis

    by oldgoat
    Replies
    1
    Views
    2,264

    11M 4TH Axis

    Sooooo....

    I have a Tsudakoma RNCV-200L Rotary Table. It is driven by a A06B-0642-B011 Yellow Cap Servo Motor. I installed the A06B-6047-H002 Drive which came with the table, as well as a...
  3. Replies
    0
    Views
    1,340

    Eguro Nuclet 10

    I am looking for a wiring diagram and hopefully the PLC (PMC) listing for an Eguro Nuclet 10 with a Fanuc 3T married to an Omron Sysmac-M5R PLC circa 1984. If anyone is willing to share this, I would...
  4. Replies
    0
    Views
    541

    Eguro Nuclet 10

    I'm hunting for a wiring diagram and hopefully a PLC program printout for an Eguro Nuclet 10 with a Fanuc 3T married to an Omron Sysmac M5R series PLC circa 1984. If anyone has access to the above I...
  5. Replies
    14
    Views
    2,375

    Guhl is correct. If you are reading the encoder...

    Guhl is correct. If you are reading the encoder signals at your new control, then 9 chances out of 10 your motor does NOT have a tach installed. The Fanuc drives receive the tach signal from the main...
  6. Thread: VCU Connector

    by oldgoat
    Replies
    6
    Views
    1,497

    The maintenance manual I have does not call out...

    The maintenance manual I have does not call out the actual connector part number, just the CN2 designation. I do not have a connection manual nor do I have an actual Fanuc Part #, but that would be...
  7. Thread: VCU Connector

    by oldgoat
    Replies
    6
    Views
    1,497

    As requested, pictures of the connector in...

    As requested, pictures of the connector in question...
  8. Thread: VCU Connector

    by oldgoat
    Replies
    6
    Views
    1,497

    VCU Connector

    I am trying to find a source to obtain the connector which fits into the CN2 socket of an A06B-6047-Hxxx Velocity Control Unit. This would be the six pin connector on the top board which supplies the...
  9. Replies
    1
    Views
    1,075

    Fanuc 11 Monitor

    Has anyone ever tried and managed to get one of these convertor boards working with a FS11 (or FS6, FS10, FS12) for a successful monitor replacement ??
    ...
  10. Replies
    11
    Views
    1,305

    #P = #Q MOD #R Or as Fanuc notates it: #i = #j...

    #P = #Q MOD #R

    Or as Fanuc notates it: #i = #j MOD #k (Remainder)

    Extracted from the custom macro section of a Fanuc manual.
  11. Replies
    19
    Views
    3,614

    Brain food

    www.prodsa.com.ar - /integradores/Manuales Tecnicos/Servo_FANUC_Motion/CNC/CNC/iDocs for CNC/
  12. Replies
    14
    Views
    3,460

    OK, I'm not sure if this is what you are looking...

    OK, I'm not sure if this is what you are looking for, it has been at least 15 years since I touched a 6T control.

    Parameter 010.2 [PROD]

    1: Position programmed in present value display is...
  13. Replies
    1
    Views
    1,665

    Hitachi Seiki Micon 16-II

    I'm hoping to find some M16-II expertise who can help.

    Have a Hitachi Seiki HC400 with a Fanuc 15MA married to a Micon 16-II. Machine was running fine today for a few hours with no problems and...
  14. Replies
    14
    Views
    4,854

    Bill, You are exactly correct. We currently have...

    Bill,
    You are exactly correct. We currently have two HMCs, and setting tool length offsets can be a real bear for the uninitiated, as well as for us initiated types. We regularly machine multiple...
  15. Replies
    14
    Views
    4,854

    My guess is clear was a relative term for the...

    My guess is clear was a relative term for the manual writers at Fanuc.



    From what I could gather, the following parameters need to be set in conjunction with TLMB for a Series 15M:

    6002.6...
  16. Replies
    14
    Views
    4,854

    I noticed that there is a 9000 option par for...

    I noticed that there is a 9000 option par for Tool Length Measurement?

    As well as a few other things which need to be worked around. I do not want to get into a discussion of why it cannot be...
  17. Replies
    14
    Views
    4,854

    Al, While there is a detailed description of...

    Al,

    While there is a detailed description of how TLMB works in the Operator's Manual from an operator's point of view, it does not describe any of the details of what happens "behind the panel"...
  18. Replies
    14
    Views
    4,854

    Tool Measurement B

    After lurking in the forums for a while, I would just like to say I am amazed at the amount of knowledge and the helpful attitude of the members of CNC Zone.

    That being said, I was hoping to find...
  19. Replies
    8
    Views
    1,219

    Email sent with what I have. If I can be of any...

    Email sent with what I have. If I can be of any further assistance, please feel free to continue this thread so all may share in any knowledge.

    The only reimbursement necessary is to hear you have...
  20. Replies
    8
    Views
    1,219

    This is a shot of the main control panel. If the...

    This is a shot of the main control panel. If the machine your working on at least appears the same, there might be a shot they did not change a whole lot. Like I said, this machine is NOT a MKII, but...
  21. Replies
    8
    Views
    1,219

    Did you ever resolve this issue? I have access...

    Did you ever resolve this issue?

    I have access to a VA-55, but I am not sure what a MK II is. I would guess this means it is a second generation, or issue, beyond what we have.

    Info for machine...
Results 1 to 21 of 21