Hello, need some help! I am programming a V-shape groove on the OD of a part with some radii. Usually i am not using G41/42 for simple parts. This one is a bit more complicated. I am confused. I am...
Type: Posts; User: Aylmer
Hello, need some help! I am programming a V-shape groove on the OD of a part with some radii. Usually i am not using G41/42 for simple parts. This one is a bit more complicated. I am confused. I am...
Hello, I have a Okuma LR15-M/3T machine with 5000L-G control. I got it from an auction, so I dont know the history. Machine starts up ok, but the spindle will not move. Sometimes it is working ok,...
Hello, I have a question, I have a couple of Okuma LR15 machines with live tooling, one of them has y-axis. Does someone know how to programm engraving? I programm everything in G-code, without any...
Hi, i just got a used OKUMA LR15-M/3T with osp5000L-G control from an auction and try to get it going. I have similar okumas at my shop, so I am familiar with them. I use the same program that I used...
I tried this short program, and yes, it is jerking each time as it was always changing position. If I would do M110 M109 M110 it would not jerk as it would go always to 0
I checked the parameters between the two LR15-2M machines - the one that does not have the jerking problem is i think slightly newer, but exactly same control, and it does not habe the spindle...
It jerks only the 1st time I engage it
it is jerking a lot - not allways the same, but around maybe 120-180 degree, jerking and shaking back and forth as if looking for the right position, finally find its zero position. What is ipw...
Looks like now its working right! I had 0.000 at the turning position, now i put in the value that i get after re-establishing the machine zero, some kind of machine number 327.2711 What confused me...
Thanks for the reply, Okumawiz! That with the single block and feed rate down was a good advice, somehow i did not think of that. Anyway I have set the Y zero position, and still it is doing that...
Thank you so much for the reply! I have the following problem - as soon as i deactivate the Y axis (using G136), the turret runs in rapit th the most negative Y axis direction, hitting the soft limit...
Hello, does someone now how to properly set the Y axis on the okuma lr15-my with osp5000 control? I am a little confused what to put in the turning position parameter - 0.000 or the value, that i...
Hello, does anyone have an idea how to disable an axis on a Okuma LR15-2m Machine? I have live tooling that i am not using, and the BL-D drivers are often failing , so i would gladly disable them to...
Hi Kotronik, did you have success with the procedure as by doctorcnc? Please let me know, i have same problem, and my problem is that CN10 is wired only on 1,2,3,6,7. and not on 19&20
Hello Doctorcnc, i am trying to disable an axis as you dicribed, but on the CN10 there are only 5 wires going to that connector, and they are on 1,2,3, 6,7. If i connect 19 and 20, there are no wires.
Hello, i am used to work on Okuma machines, now i got a Colchester Tornado cnc lathe with fanuc 18i-TB controll. Now i have to learn a lot of new things with that control. As simple as it can get,...
Hello,
i got a used Okuma LR 15-2m Mashine. It has 3 turrets. Now the problem I have is with the two upper turrets. Actually i dont use the third turret. Both ot those turrets do not index,...
Hello
after starting the machine the display shows "Check Soft"
it is osp5000L
What does this mean
Thanks
Waldemar
Hello,
I have 2 okuma LB15 with osp5000l without IGF. Somebody a idea how to get the IGF Software on the machine? I asked already okuma support, but they are not able to do that. I know that there...
Hi, i just bought a used okuma LB15 2M machine. The alarm comes on upon turning on the machine. After leaving the machine on for about 20 minutes i can reset the alarm. I am not sure if it would come...