523,979 active members*
1,286 visitors online*
Register for free
Login

Search:

Type: Posts; User: mbservice

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: pls, is there a bar puller design, for pulling at rpm 0 ?

    Why can't you stop the spindle?
    I'd go for coolant operated one
  2. Re: Manual for Colchester Combi 3000 with Fanuc 210i-T control

    Have you set the I/O to 4 on the setting page and set the combi to look at the card and not at the setting folder&nbsp;<br>Private message me I have manuals&nbsp;
  3. Re: Manual for Colchester Combi 3000 with Fanuc 210i-T control

    Have you set the I/O to 4 on the setting page and set the combi to look at the card and not at the setting folder
    Private message me I have manuals
  4. Replies
    3
    Views
    500

    Re: Fanuc OTc 414 X axis detect error alarm

    have sent you a pm
  5. Replies
    3
    Views
    500

    Re: Fanuc OTc 414 X axis detect error alarm

    Did you check the encoder ?
  6. Re: 1337/5000 TNC155: Data in RAM but inaccessible

    Your batteries have failed
    When the parameters are loaded they would come up with a ? You would not be a me to go back it would come up with a ? Again
    Unless all the parameters are fully loaded
  7. Re: Bridgeport Interact 1 Mk2 with TNC 2500 missing 110V on wire 8 and 9 when power o

    nikos
    Did you check the overtravel switches
  8. Replies
    16
    Views
    4,328

    Re: Colchester 2000L

    What turret do you have ? Do you have a barfeed? What is your problem?
  9. Re: Bridgeport series 1 interact TNC 145 Gross positioning error B

    Check your speed parameters
  10. Replies
    11
    Views
    1,642

    Re: Colchester Tornado 200 Lathe parameters

    Hi Vlad
    Tornado 100 parameters will be close but not correct as there are different models and veraions of the machine you may cause damage to your drives please send me your email address in a...
  11. Thread: Fanuc 21i TB

    by mbservice
    Replies
    3
    Views
    42

    Re: Fanuc 21i TB

    What do you mean it won't pick up the wear offset
  12. Replies
    3
    Views
    28

    Re: Fanuc Flash Card

    Use the SRAM service page
  13. Replies
    2
    Views
    738

    Re: align MF Sprint 65 Revolver

    Dont suppose you have a back up of your machine
  14. Replies
    0
    Views
    163

    Re: help for fanuc 0-TT

    What is your incoming supply ?
    Where are you getting 410V
  15. Replies
    3
    Views
    46

    Re: YAM lathe with 6t

    Try stopping spindle , turning off coolant etc to see why it's not stopping
  16. Replies
    3
    Views
    46

    Re: YAM lathe with 6t

    What happens if you change M00 to M30 does program stop and reset
  17. Re: Replacment battery backup board for HAAS Machines

    How much please pm me
  18. Re: Parameters for Colchester 2000 with 0-TC control and 8 station Duplomatic turret

    Did you get the lathe going
  19. Re: EX1104 TURRET CLAMP/UNCLAMP SENSOR ERROR or OVER 1SEC

    Does the turret release within 1 second may be wise to remove sensor check it's working and clean it
  20. Re: 1337/5000 TNC155: Data in RAM but inaccessible

    What happens if you load all parameters then reboot system
  21. Re: 1337/5000 TNC155: Data in RAM but inaccessible

    If you type in the correct value and press ent does the value change
    When you're accessing them do you put in the unlock code
  22. Replies
    7
    Views
    931

    Re: PMC Of Colchester Electronic Triumph

    Hi yes I have parameters for your machine please send the serial number and your email
  23. Replies
    11
    Views
    1,642

    Re: Colchester Tornado 200 Lathe parameters

    What does it say on the screen when you power up
  24. Re: HELP! CNC Engineer needed, any thoughts?

    Private Message me if any problems Im in Kent
  25. Replies
    4
    Views
    51

    Re: Colchester 2000L Parameters

    Brent messaged you its nothing to do with parameters I work on thise all the time
  26. Re: Dugard eagle 100 lathe. Fanuc series oi mate-tc

    Chuck sensors? What alarm is on the drive
  27. Replies
    1
    Views
    55

    Re: Colchester mbf1000 barfeed issue

    Have you set the number of bars you want to run in the barfeed operation page
  28. Replies
    1
    Views
    54

    Re: Fanuc noob question q setter

    Only if you have told the control you are using that tool in MDI
  29. Re: Bridgeport Interact Series 1 - TNC145 Tapping Cycle Issues

    Message me your email or phone number and I'll send you a pic as I'm in Kent
  30. Re: Bridgeport Interact Series 1 - TNC145 Tapping Cycle Issues

    You may be able to get away with spring loaded collets dependant on speeds and tap size
    Where are you based
Results 1 to 30 of 461
Page 1 of 16 1 2 3 4