Hi!
I have a SX3 that i need to wire up, it came with everything disconnected for spindle motor, but all components are there
What i need is a schematic that includes the RFI filter and also a...
Type: Posts; User: xillianto
Hi!
I have a SX3 that i need to wire up, it came with everything disconnected for spindle motor, but all components are there
What i need is a schematic that includes the RFI filter and also a...
look at emgprecision.com based in UK, ask for a 6 poled spindle, should handle steel but does not have as high rpm (i belive 8 or 12000 is max)
Sent fra min SM-G975F via Tapatalk
I have currently set the spindle nose as tool 0 and every tool is calculated from that, so all tools are positive from that offcourse.
tool changes works, but now and then it stops working after...
i belive so too, as when i checked the macro on the cnc comp, it was fine
Sent fra min SM-G975F via Tapatalk
good tip ger :)
Sent fra min SM-G975F via Tapatalk
thanks, will correct that, anything else that could get the cnc to act up ? it does do it's job, but all og the sudden it will just stop working when doing manual tool changing.
Sent fra min...
Hi, i got a friend of mine wrighting a little m6 script for me as i change my tool manual on my BT30 spindle, script does what it should do, but i got a problem that it sometimes locks UCCNC up abit,...
it's set up for flood cooling for sure :)
And yes, i am quite happy with the spindle, it's 3kw 4 poled so it has allot more torque than regular spindles.
I have tried steel aswell, and that...
Very nice build :) Any plans of replacing wood parts with aluminium ?
This is regular concrete with rebars :)https://uploads.tapatalk-cdn.com/20201109/ce06507cb659b90c4ac9556e1bae325d.jpg
Sent...
Hi, what i did is that i just connected the override limit to the pins, and then i have connected that pin to reset in UCCNC, i belive it's code 152 on pin setup
Sent fra min SM-G975F via Tapatalk
Hi, gotten this to work ? I use this one quite similar, just with chip blowoff.
Hi, i was reading trough this page, and yes.. if you do have ceramic bearings, you wont get ground at tool actually, so that should explain the failure on that probing.
As a future controller, i...
No sorry, only some progress pic on facebook groups, but here is a fresh pic441472
Sent fra min SM-G975F via Tapatalk
Hi, Have not had any problems with cracking for the almost 2 1/2 year that i have had the frame.
it stays dimentially stable aswell as i can measure.
there is very mutch rebars in it though
but...
He is not the only one who has been thinking about concrete, Mine is reinforced with 12mm rebars every 50mm, with 10mm steelplates inserted for rails.
Then levled the plates with epoxy before...
Skriv iallefall tykkelse/lengde så er det lettere og si om det er noen som trenger ;)
Sent fra min SM-G930F via Tapatalk
I would have gone with uc300 and uccnc aswell if i didnt have my pokeys57cnc board and mach4 lisence
Sent fra min SM-G930F via Tapatalk
Not the like the one from 2010 /2017 screenset to have a fixed plate between tools
Sent fra min SM-G930F via Tapatalk
I wish i could, but i have pokeys57cnc controller with mach4
Sent fra min SM-G930F via Tapatalk
Too bad :( i wanted auto z tool measurement
Sent fra min SM-G930F via Tapatalk
Ger, abit wrong place.. but will there be auto probe for mach4 or perhaps a screenset if possible ?
Sent fra min SM-G930F via Tapatalk
Looking good :) this will be a good pick foe me when doing the change to uc300eth and uccnc.. just have to get the incime for it first (i mainly let the machine pay for itself)
Sent fra min...
And now this board became hell lot more tempting! Have been looking at uc300eth for a while
Sent fra min SM-G930F via Tapatalk
Noen som har skjermede 4 ledet kabel ??? Trenger 15-20m av det til motorer/spindel
Sitter du igjen med noe deler enda mon tro ?
Er på jakt etter en motor og driver extra.
Trenger da en:
Longs Motor 23SH9430 Nema 23
Longs Motor DM542A Driver
Er også på jakt etter en vannkjølt spindel med VDF om noen har dette...
fikk du solgt denne ?
Den 3D printeren din, hvor sterk er plastikken vist jeg skulle hatt 1.5 mm emner ? Og hva er kostnaden på slikt materiale ? Evnt om du har noe plast i den tykkelsen og frese ut på ? Om ikke så tenkte...
Contact me and i might be able to design
ble det noe mer med dette ??