508,501 active members
2,983 visitors online
Register for free
Login

Search:

Type: Posts; User: NICK1945

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,707

    Re: Tornado A90 with MBF-1000 M19

    You can set it in the Bar feeder page after it has homed..............
  2. Replies
    2
    Views
    606

    Re: All about the cnc DAHLIH

    Need procedure to set zero return on Dahlih MCV-500 on B axis I have APC 300 alarm due to dead battery
  3. Replies
    13
    Views
    3,865

    Re: Colchester 2000L

    Yes what is the problem?
  4. Replies
    1
    Views
    398

    Re: tornado 220 fanuc 21i control

    Hi on mdi or auto it needs to see the door closed and the chuck clamped............
  5. Replies
    11
    Views
    1,165

    Re: Colchester CNC 2000

    Hi
    For the machine to run in auto it needs the door closed and it needs to know that the chuck is closed.
    nsafos@Canadianmachinetools.ca
  6. Replies
    1
    Views
    1,052

    Re: colchester combi 4000

    Hi I can help you with those problems I also located in Toronto Ontario sent me an email at nsafos@canadianmachinetools.ca
  7. Replies
    30
    Views
    4,305

    Hi What is the model and serial number of that...

    Hi
    What is the model and serial number of that machine is it a Harrison Alpha 400 or Alpha 550. and what year is it
  8. Replies
    30
    Views
    4,305

    HI I was out of the country i did sent you the...

    HI
    I was out of the country i did sent you the procedures tonite
  9. Replies
    13
    Views
    3,865

    Colchester 2000L

    I have the parameters as fot diagnostics please tell me what type of turret you have how many stations?
  10. Replies
    4
    Views
    754

    colchester 300

    The problem is you missing 24 V DC
    There are two versions depending how old it is The first one had an E-stop board behind the main disconnect switch on the electrical cabinet usually the relay...
  11. Replies
    5
    Views
    750

    blown Fx14 fuse on Fanuc power supply

    This fuse protects the +24V on the machine it means you are having a short on the machine wiring side check the resistance of +24V to ground and try to isolate the fault.
  12. Replies
    30
    Views
    4,305

    zero return procedures for colchester cnc lathes

    HI all
    If any body needs zero return procedures for colchester or Harrison lathes sent me an email with the model number and i will sent you a procedure.
    My email is...
  13. Replies
    4
    Views
    726

    Hi Kamal what is the serial number and is it an...

    Hi Kamal what is the serial number and is it an electronic triumph instead of electric i have a lot of info
  14. Replies
    2
    Views
    513

    Hi CNC Boss i am an x 600 service engineer and i...

    Hi CNC Boss
    i am an x 600 service engineer and i can sent you the procedure this is my email
    nsafos@hotmail.com
  15. Replies
    5
    Views
    483

    tornado thermal alarm

    Hi Gordon
    If you open the encoder cover there are two white wires small gage going to the motor this is for the thermal switch normally closed you can check with a digital voltmeter they should read...
  16. Replies
    1
    Views
    354

    chances are that you moved the machine recently...

    chances are that you moved the machine recently and you need to change the two phases in order to correct the phase .
    I f you open the back you will see two hoses going to the spindle the big hose...
  17. Replies
    2
    Views
    551

    You have two plugs that plug on the screen one of...

    You have two plugs that plug on the screen one of them has the +24V and the other connects to the crt output from the control also check that you have filament light on the CRT
  18. Thread: Tornado 200

    by NICK1945
    Replies
    2
    Views
    736

    cooland in hydraulic tank

    Hi try not to plug drawtube in the back of the lathe extra cooland might be shiping in the hydraulics through the drawtube threaded part that connects on the chucking cylinder.
  19. Replies
    2
    Views
    627

    yes i can get you the parameters you will also...

    yes i can get you the parameters you will also need the diagnostics
  20. If you have two pins they will be in the front of...

    If you have two pins they will be in the front of the turret.
    You might have a series of bolts in the front of the turret and if you loosen them you can turn the disk from side to side.
    Or you have...
  21. Replies
    0
    Views
    357

    OKK spindle sensor procedure PCV-55

    I am having difficulty in setting spindle sensor cannot orientate spindle rpm is good any help would be appreciated. especially a procedure for setting upthe spindle sensor....
  22. Replies
    6
    Views
    423

    also check the two pads in the back of the...

    also check the two pads in the back of the machine they will affect the column and those the squareness to the x axis.
  23. Replies
    7
    Views
    605

    you might want to check your parameter setings on...

    you might want to check your parameter setings on your 0 T control
  24. If a turret has been crashed you need to check...

    If a turret has been crashed you need to check two things.
    1. Put an indicator and check that the face of the turret is perpendicular to the chuck when you move the x axis up and down.
    2. Check a...
  25. Replies
    6
    Views
    694

    hi dbarath did you get your turret problem...

    hi dbarath did you get your turret problem resolved if not give me a call at 647 308 3375
Results 1 to 25 of 44
Page 1 of 2 1 2