508,504 active members
4,256 visitors online
Register for free
Login

Search:

Type: Posts; User: sportybob

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    80

    Re: Single Board Upgrade

    Hi Jonrya. I can answer all your questions.

    Give me a call.

    sportybob
    952-288-6340
  2. Re: centurion 4 IV periodically freaks out

    Hi Brian, might need to check the power supply voltages.

    I have C4 parts
    give me a call.
    sportybob
    952-288-6340
  3. Re: ERROR 402: Y-Axis software limit overtravel

    Hi Chud. I can help with your machine.

    Give Me a call.
    952-288-6340

    sportybob
  4. Replies
    4
    Views
    106

    Re: Milltronics - Glentek GA370-3

    when check for drive faults it take 2 people. one to press the reset button on the front panel and one to watch for a red fault light. there are 4 red leds. depending on which light comes on will...
  5. Re: Milltronics P1 skipping tool change in DNC

    Try turning on the arc filters in the cadcam.

    sportybob
  6. Re: Milltronics P1 skipping tool change in DNC

    The tool changer issue is most likely a "in position" error. check the following error and see if it hanging up at .005

    When it comes to SBC updates you should all call me. I have the answers.
    ...
  7. Replies
    4
    Views
    125

    Re: Milltronics Partner 1 not booting

    Hi Nick, I have power supplies.
    Give me a call.

    Bob M
    952-288-6340
    Sportybob
  8. Replies
    1
    Views
    121

    Re: RW15 - Did i erased parameters?

    unless someone made a "special" M or G code file to run, the peck id built into the software. the tool change macro should be located in the "TC" folder.

    call me 952-288-6340

    sportybob
  9. Re: Couple of questions MB19 and centruion 6

    Yes the external keyboard is hot swappable and yes it works in conjunction with the front panel.

    yes you can change to the CNC software.

    call me, 952-288-6340

    sportybob
  10. Replies
    3
    Views
    177

    Re: Monitor has problems on start up

    Your CMOS battery on the mother board is about to die.

    Give me a call
    952-288-6340

    sportybob
  11. Re: VM16F - upgrade VFD/spindle - anyone done it?

    Hi Erik, you say you have a MC5 drive. I will assume that it is a 626MC5. These are NOT easily changed out for another drive. These came in 2 versions, 1. a single speed and 2. a 2 speed. the 2...
  12. Re: Partner 1F movement twice what display reads out

    Hi Johnson. try setting the encoder multiplier to 1. Cycle power. try a Jog "distance if about 5inches and measure with a tape measure.
    Some times the pulleys have been changed from 2:1 to 1:1...
  13. Replies
    4
    Views
    249

    Re: Centurion IV Ramill VI DNC Help

    The RS-23 in the C4 control is OLD, OLD school. I will assume that you are running a Win 7 / Win 10 PC. Not sure what DNC software you are running. but there is a setting for "FIFO" buffers, (...
  14. Replies
    6
    Views
    348

    Re: Miltronics VM 25 with 7 control

    Hi Positiverake, Turn that parameter off. That way it will not display G5x in Z. then it will just have and use the "Z tool" to your top of part.

    sportybob

    Call if you have questions....
  15. Replies
    6
    Views
    348

    Re: Miltronics VM 25 with 7 control

    There is a MISC parameter "G54 in Z axis" that may have been tuned on. this would place a "F-key button" in Z hand wheel to set the G5x Z value. toggle that parameter to NO. that will turn off that...
  16. Replies
    6
    Views
    348

    Re: Miltronics VM 25 with 7 control

    Hi Positive, you are not clear if the machine has a tool setter, or if you are using the "RUN, TL set program.

    turn on block mode and it will "step" you thru the program, the text code will...
  17. Replies
    6
    Views
    230

    Re: Milltronics Partner 1F throwing tools?

    Call me

    sportybob
    952-288-6340
  18. Replies
    0
    Views
    241

    Re: 2005 RW15 Thrust Bearings

    HI Brian, VXB handles mostly cheap Chinese bearings.
    My BG-01 (NSK or SKF) are $48.00 ea. usually sold in pairs and I through in a new .002" shim.

    I also have a NSK matched duplex set I call the...
  19. Replies
    0
    Views
    241

    Re: 2005 RW15 Thrust Bearings

    Hi Copelan, Sorry for the delay, I did not see this post earlier. The RW-15 uses a matched pair 20TAC47 bearings. ( Milltro P/N BG-102)
    I stock these for $ 225.00 (pair) + Shipping
    I stock NSK. ...
  20. Replies
    15
    Views
    504

    Re: Partner 1D Tool Holders.

    HI Sen2, the CNMG432 is the most widely used lathe bit. you should not have any trouble selling or swapping them with other shops. you just need to know what insert and what it fits or swapping for....
  21. Re: Purchased Two Partner 1 Mills- I have a few questions

    PM me Your email

    sportybob
  22. Replies
    4
    Views
    203

    Re: X axis way covers

    HI Don, On the end of the table are the wipers, remove the 4 screws holding the wiper mount plate to the end of the table.

    I have motors / drives etc. open till 9pm Mon - Sat.

    Give me a call ...
  23. Replies
    8
    Views
    302

    Re: Milltronics Partner 1 Series H CAM

    HI SEK22, The multi function drive is hot swap. One should try and avoid booting up with the card installed. some motherboards don't like that.

    sportybob
  24. Replies
    8
    Views
    302

    Re: Milltronics Partner 1 Series H CAM

    Hi SEK22,and ALL. If a machine has a single board control update, I have a program I wrote so the control will "unzip" a zipped up file.
    What this means is that a "floppy sector / disk" will hold...
  25. Replies
    37
    Views
    795

    Re: Partner 1 Series H - Problem with Video

    Hi Jonrya, We talked on Saturday. You lost the parameters when changing the simdisk battery. Sorry, I came down with a major case of the CRUDS. I still have not made it into the shop. Hopefully...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4