Search:

Well I Got it , 1201.7=0 ,3402.6=1 , 3409.7=0 , 5003.6=1 ,5003.7=1 Thanks everyone!

Thanks for the reply Zavateandu, yeah they were both set to one, I don't know? I will keep digging, thanks again

No Dice, I think it would be in the Edit/CRT part of the Parameter Book but I can't find it. Thanks for the Reply

Will do, let you know

Hello, I'm trying to find the parameter so when I hit reset it will change the tool number on program check screen, like T0202 hit reset and now it shows T0200 you know dumps the offset. it is...

It's been a while since I ran one of these, I think you use Tool Measure button on the controller instead of the "M" X "M" Z , Try Typing X 1.5 or whatever, press Tool Measure button on the...

Hello, anybody using Doosan sketch turn? if so, how do you like it and what does it cost? Thanks.

Hello, is there a way to edit the post for super cap? this is a fanuc 18i control, when it sends the program to the NC side its full of crap and I want to change the way it posts. this is a 2001...

Hello I was wondering how do most people set up there tools on a Gang tool lathe, do you keep them in order 1234 from front to back etc or are they all over the place, do you stick out your turning...

Any idea what ones?

Hello, this is a Harding GT SP with fanuc 18i when I try to zero return with the buttons on the panel nothing happens but G28 works, is this one of Hardinge's secret buttons that's turned off? ...

Heavy, thanks' for the reply, yeah I looked at "that parameter" and it's on and like I said the G83 etc. works so I don't know what it is. anyway I'm making parts with the G32 (maybe I'll make a...

Heavy, you assumed rite just like the program shows, this machine does not have live tools just a plain 2 axis lathe. and yes I am tapping with a sponge holder and a G32 and that works, I was...

Superman, G57 works fine, use G54-G59 all the time, I do both ends of a part a lot. Tried dumping the R did not help and yes the feed is for a 1/8-27 NPT , I have all the hole making cycles G83...

Thanks for the reply. heres the code

G0T0909
G50S2500M8
G97S300M3
G57
X0Z.15
G99
G84Z-.5R0F.037
G80

This is on a okuma howa lathe with Fanuc 18iTB the G84 will feed in but then just sits there and will not reveres out? any help would be great. Thanks

Hello all, want to change this okuma howa lathe with a Fanuc 18T so when I use Z 0 Measure to set a tool on the Geometry page it wont use the G54 ect. in its calculation, is there a parameter for...

Yep the button worked, and I did find the parameters I needed to change, everything works as it should. thanks for the help!

Interesting, thanks for the reply

This is a 1998 deawoo puma 200 lathe, Had to remove the alignment button on the turret so I could indicate the tool Holders(blocks) in, I guess the machine had been crashed hard but had been fixed, I...

the measure soft key don't work, say I was indicating a drill and key in X0 measure it sets the geometry to 0 and not the real number, it has a the input C soft key, this is on a deawoo puma 200 with...

Yeah maybe, its a pain compared to other controls.Thanks for the reply

Anybody know how to get the tool offset measure button to work? this is on a hardinge chnc 2+ with a General Numeric GN10 control and is the soft key on the control, geometry, work shift. any help...

Just started running a DMG MORI NLX2500/700 with the Celos Mapps V control, in the manual it shows the fist line of a G76 cycle not using a Q (min depth of cut) in it. anybody use it? everything...

On my samsung SL-65MC with fanuc 0i I will program a G28 H0; M5 that way it will zero out before it disengaging. I like having a zero in C on the screen when I'm not using C axis

I found it, just a few pages down from where you were in that book. thanks !

Ill take a look thanks for the reply

fanuc 0i with manual guide i this is a horizontal lathe and the manual guide i thinks its a vertical, anybody know how to change this? thanks

thanks for the reply, yes I want to just display in the variable page

Hello, I want to have a name for each of the permanent variables I use like #500 TAILSTK this is on a fanuc 0i control, seems like I did this on another 0i but I cant get this to work, tryed the...