Good day!
We are going to use two KStep board in one mashine (using one KFLOP).
1. How to conect KFLOP with second KStep board? (what JP we need to use?)
2. What additional connecting wire we...
Type: Posts; User: RuslanRobot
Good day!
We are going to use two KStep board in one mashine (using one KFLOP).
1. How to conect KFLOP with second KStep board? (what JP we need to use?)
2. What additional connecting wire we...
I find!
https://www.youtube.com/watch?v=uQWDttzKuDA&ab_channel=Dynomotion
Thanks!
Please help me.
How do I make the manual control arrows on the KMotionCNC panel inactive (turn off)? See the photo - circled in red. So that I can then turn it on if necessary.
I need it in order...
YES! Work. Thank you!
Good day!
Help please.
Here is the InitKstep4axis file (compiled without errors). I configured the INIT button on the KMotionCNC panel that runs file InitKstep4axis.
Before flashing, when...
Good day!
kStep board - warms up to 75 degrees Celsius, Kflop is heated to 52 degrees Celsius. See video: https://drive.google.com/file/d/17rL9gEgJiFfz4vynVt2tg7EyFqF6V6d3/view
Warms 75 degrees...
Good day!
kStep board-warms up to 75 degrees Celsius, Kflop is heated to 52 degrees Celsius. See video: https://drive.google.com/file/d/17rL9gEgJiFfz4vynVt2tg7EyFqF6V6d3/view?usp=sharing
We use...
On a conventional stepper motor driver, the micro-step mode is set by dip switches according to the table.
1. Where are microstep settings in Kstep?
2. How to do auto-tuning microsteps in Kstep?
Let me reformulate my question (as am not sure, that I understand your answer):
Opto isolated relay consume 9 milliamperes, 3.3V. Can we connect this relay to JP4 or JP6? Will this load spoil...
We are going to use opto isolated relay, and connect it to JP4 or JP6 - can you advise what better? (JP7 used with KStep).
Where is described the milliampere current on JP4 and JP6? - we can't find...
I see the KStep Amplifier for KFLOP https://www.dynomotion.com/KStep.html
It will drive 4 motors and emit heat.
I don't understand - How to cool this board?
Shold I buy radiator? - but I don't...
Good day!
I have 4 step motors, 1 stop buton, 8 end sensors, 4 pneumo relay for suction cups.
I am going to buy 1) KFLOP, 2) KStep Microstepper Amplifier for KFLOP.
Do I need to buy...
Here is the specification on my driver (it is on russian, please translate it by google)
https://darxton.ru/files/pdf/stepperdrive/EM402.pdf
Please tell me, - will it work with Kflop?
1. I bought another driver - Leadshine EM 402 (it supported CW/CCW mode). On the scheme, driver require VCC and ENABLE. What pins I have to connect on the Kflop to be connected to VCC and ENABLE? ...
This connection scheme was the plan, but in fact we wrong connected. So we need to do in accordance with this scheme.
No, my drives don't need to be enabled.
Thank you!
Can you tell me please , - is this connection scheme right?
It seems to me, that in fact we connected something wrong.
I did these:
1. To use Open Collector - Step/Dir mode, changed in the Init file: ch2->OutputChan0=2; ch3->OutputChan0=3; for axis Z and A respectively. The motors DON’T move, but the KMotion shows...
Good day!
I use this driver to control suction cups, axis A and Z, using micro step 16.
After performing the Zero Axis, all suction cups are aligned. After starting the loop 100 times (G code Axis...
Yes!!!!
I am idiot. I tried to make Kflop work while ESTOP is on.....
Everything is work.
Thank you very much!
1. I pressed the button Home, - to home all axis (see file HOME_Axis.c). Machine start to go home, and during this I turned off the power.
2. After 15 sec. I turn on the power. But in the screen of...
EStop button.
EStopDisablesAll.c - Yes, i found this file, changed number of bit (inputs 10, bit 1034).
On the menu M0-M30 in front of the Stop, choose Executing Prog, set number of program (Thread...
Please, help me.
I have two questions with sensors:
1. I can't find where in the system KFLOP I can invert the input signal from end sensors. I have several end sensors of the Normally Open...
Yes!!!
I did in accordance with your screen shot, and I can turn on/of lights on the board by G-code (M100 - lights on, M101 - lights off).
But I connected relay to the Konnect without flyback...
Please help!
I dont understand - how to make alive my pneumo-relay.
I have KFLOP + Konnect Optical I/O Expansion Board.
Pneumo-relay connected to Konnect pins Out 12, 13, 14, 15.
In the...
Yes it 's work!!! Thank you.
Please, we need help!!!
What was done (see attached files):
Konnect was connected to the Kflop through jp6 whith a ribbon cable that was lying in the kit;
in a C-file a Konnect board was...