Search:

HI,
It is for few days I have problem with my spindle noise and by accelerating in high gear from 0 to 2000 rpm above, it start to make a huge noise like something is fighting the motor and the...

I have a Mazak H500 (HMC), while ago by start-up the spindle in high gear (2 stage gear box low & high), you could get scare by the spindle noise specially at 2000 rpm above and then without any...

Hi, Thank you very much for your valuable information.
How we can find the meaning of any format like what I have in my parameter which before install new system disk the value of parameter S1 was...

I have Multiplex 610 and few days ago the machine had collision because of picking-up next tool offset as 0.
I reinitialized the controlloer then I recieve alarm: 44 Parameter error.
I can transfer...

Hi,
Few days ago there was a kind of explosion on my KMSSTR2R contactor (it might be because of heat) and 2 glass fuse was blowened on my FR-SF which all of them has been replaced.
I start the...

Contact Berthold Herlmle Ag In Gosheim Germany.
They might help you.

Many thanks to your reply Botha.Y, I have also some alarm list of FR-SF drive and repaired many times this unit but I have never seen Alarm 43.
I did google search but no sign of this alarm but it...

Hi,
I have a Mazak Multiplx 620 with 32-6 control, few days ago the machine stopped in the middle of machining all of the sudden with spindle error on head 2 and it is intermittent alarm but in the...

On my servo drive there is a another board RG201B which cause the problem and the alarm number on this board is 30.

Hi, I hava a mazak Multiplx 620 few days back the machine was stopped with following alarm: 37 OVER REGENERATION.
The alarm description and action does not help me, every time when I turn on the...

First check continuty on your feed back cable from encoder to controller and your incoming power cable and voltage to the motor and at the end your encoder.

With Heidenhain control usually there is a red botton back in the electrical & control cabin and if I am not wrong it is taged by S3 (In some machine manufacturer it is not there), you should power...

Hi there, I have a Hitachi Seiki Hicell with seicos L III control, aftyer turning on in the morning, to do referencing all the axis I get alarm: 950 x axis 1-revolution sig. error.
I can do home...

On which head you get the alarm (HD1 or HD2)???
Have you check coupling between motor & ball screw??? If it is fine change your controller (I think RG221B or A) from head 1 or 2, to head 2 or 1 and...

Hi,
One day morning my gantry loader robot flex-GL50 head (hand) start to rotate CCW as soon as I turn on the robot control, it does not stop at all and twisted all the pneumatic pipes and proximity...

Hi,
I have a Mazak H500-M32 and recently in the middle of machining and by the moment of picking-up the tool from magezine or puting it back the tool in to the magazine by shifter, the alarm 45...

THERE ARE 2 GEARS, 2 SENSORS & A PRE-AMP.
I KNEW THAT I MIGHT NEED SCOPE BUT I WAS WISHING THAT IF THERE IS ANOTHER AWAY TO ADJUST IT.
ANY WAY THANK YOU ALL.

Hi,
Few days ago my C-Axis on my Multiplex 620 on Head 2 could not find reference position and was running without stoping.
I replaced PLG sensor and pre-amp with another one the result is that the...

Hi,
Does any one have any information about coolant ribbon filtration or to filter the coolant without losing coolant quality and pressure on outlet up to 100 micron for MPX 620 Lathe or how can...

Thanks guys, the problem is that Rod Shifter is broken and one of the gears is worn out the problem was mechanical and now it is about a week I am looking for the parts, except Mazak does any one...

Hi,
This morning after turning on the machine and running the program, the spindle could not run in Low gear but it can shift to high gear and run (in low gear the spindle motor is running but not...

Hi,
If you did test all the dk434, do you know how many you may needed??? the crack does not mean the the part is not good.
Any way send me your e-mail then I will send you his details in China, I...

Hi,
Can you check if it is your DK434 or not??? there is a procedure ofr checking those bloody DK434.
I have repaired few weeks ago mine and there was also few IGBT damaged, check also your IGBTs....

Hi,
The machine was stopped at the end of program by changing pallet No.:2 with No.:1 (To put Back Pallet No.:2) and there was no alarm.
The machine does not unclamp the table and also there is no...

Hi Htech,
I know it has been for ages that you post this thread but I am wondering if you have still the procedure to nuclamp the pallet???
I appreciate any information regarding this.
Karan

Hi,
Usually when you have system malfunction, it might be your processor or your parameters need to be re-initialize (because you mentioned that the battery has been changed, I am do not know what...

Hi,
I have changed MC116 on my control T32-6 and re-initialized the parameter & Data.
After turning on the machine there is an alarm: 16 AMPLIFIER NOT EQUIPED.
Then I replace MC116 with another...

Hi First thing that you should do to enter the parameter with Fanuc control is to change the value of PWE (Parameter Write Enable) from 0 to 1 as follow:
1- Select MDI mode and push Emergency Stop....

Hi Cut more,
It know that it has been ages that you repaired your SE-IO1, I went thoriugh all this thread and tried to undrestand it but my problem is not the same as all you guys, may be I am...

Hi Stephane,
I know it has been long time that you repaired your SE-IO1, I have some questation maybe you can help me:
1- There was 2 Triak transistor (C2939) were blowen (1 of them was broken), I...