508,393 active members
2,611 visitors online
Register for free
Login

Search:

Type: Posts; User: rl49

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    66

    Re: Centurion 6 boot up shell

    This from C6 programing manual page 158

    Get to proteacted mode then

    F9 (Shell) Main-Run-Displ-Shell
    F9 (Shell) is available if the control is in access level 2 or greater. It will Shell out...
  2. Replies
    12
    Views
    168

    Re: Milltronics P1 skipping tool change in DNC

    My P1H is serial # 2763, I am quite sure someone did the upgrade motherboard before I purchased it
  3. Replies
    12
    Views
    168

    Re: Milltronics P1 skipping tool change in DNC

    My experience with a P1E 386Dx40 1993 era machine based control as the memory limitations are very limited, I have a P1H 1995 that had a 486 control and was also limited with the ridiculous ram...
  4. Replies
    12
    Views
    168

    Re: Milltronics P1 skipping tool change in DNC

    post your code for the file you are drip feeding to see if that is the problem, I am assuming you use a cad cam app to generate the code? how big is it in megabytes? i
  5. Replies
    12
    Views
    168

    Re: Milltronics P1 skipping tool change in DNC

    What mother board do you have is it a 486 or 386 from factory and how much ram does it have? Also what software version? send screen shots of this info and we can give you a possible solution.
  6. Replies
    4
    Views
    106

    Re: Milltronics - Glentek GA370-3

    Search:
    Type: Posts; Keyword(s): 449, drive, fault; Forum = Milltronics and child forums
  7. Replies
    7
    Views
    315

    Re: MB18 Centurion 6 homing error

    Buy an encoder from Milltronics the glued disk will not last especially if not centered. if you cant get the following error adjustment with the balance adjustment, you encoder OR wiring to encoder...
  8. Replies
    35
    Views
    488

    Re: Rigid tapping toolholder

    Was it this document?
  9. Re: Add tool setting probe to Milltronics Centurion 7 knee mill???

    I believe you have to purchase the probing option from milltronics, have you contacted them?
  10. Replies
    16
    Views
    358

    Re: Questions on adding rigid tapping....

    I haven't had to do many blind hole rigid tapping almost all my experience has been with thru hole, I would suggest to experiment with wax or aluminum to dial in parameters, also do search on rigid...
  11. Replies
    16
    Views
    358

    Re: Questions on adding rigid tapping....

    Might have ti use a propane torch or map gas to free up I purchased pulley to do same with my P1E but have the P1H which has rigid taping that works well and has 45 inch x travel so I haven't gone...
  12. Replies
    16
    Views
    358

    Re: Questions on adding rigid tapping....

    as a last check I would look at bios settings in motherboard to ensure its not fighting the C5 x card for control of com2 serial port. I have experienced issues with other dos based software mainly...
  13. Replies
    16
    Views
    358

    Re: Questions on adding rigid tapping....

    I would check the pulses at the P6 connector with your voltmeter to rule out ribbon cable issues.

    On my P1H it has an CSM spindle and the PPU setting is different but it uses a resolver to...
  14. Replies
    16
    Views
    358

    Re: Questions on adding rigid tapping....

    2000, Sporty bob stated in this post https://www.cnczone.com/forums/milltronics/209846-get-actual-rpm-jive-commanded-rpm.html post #26 that fudge factor is only effective on C7 controls
  15. Replies
    16
    Views
    358

    Re: Questions on adding rigid tapping....

    Page 7 is same as my paper manual I purchased from Milltronics P1H by serial number but they sent me a non CSM spidle electrical paper manual.

    From older posts in past I dont think a parameter...
  16. Re: Partner 1F movement twice what display reads out

    I do believe you have to power off to take effect
  17. Re: Partner 1F movement twice what display reads out

    My partner 1E and 1F with DC drives are set to +10000 with an encoder multiplier of +2416068
  18. Replies
    13
    Views
    493

    Re: New to me Partner 1H questions....

    Call sportybob on the roller fabric and the wipers for way covers 952- 288-6340 , cant remember how much it was 8 years ago when I did mine but was much less than from factory.
  19. Replies
    13
    Views
    493

    Re: New to me Partner 1H questions....

    home the carousel that should set the pockets to correct position unless proximity switch is faulty. The shallow notch goes to the carousel.
    reset your tool tables to correct length and diameter as...
  20. Replies
    13
    Views
    493

    Re: New to me Partner 1H questions....

    If its a Yaskawa drive you will see an encoder belted to spindle next to drive belts to have rigid tapping .

    My P1H has a CSM which has feed back for rigid tapping inside spindle motor.
  21. Replies
    13
    Views
    493

    Re: New to me Partner 1H questions....

    My late 94 P1H mechanical Manual only shows the 10K spindle with a CSM 12.5 or 15 HP motor .

    If you have a CSM spindle motor you have rigid tapping.
  22. Replies
    37
    Views
    794

    Re: Partner 1 Series H - Problem with Video

    milltronics wont send you a parameter file with macro backups? I haven't dealt with them since last year when I upgraded my piH to a c6 control and paid $650 for software upgrade and conversion fee...
  23. Replies
    37
    Views
    794

    Re: Partner 1 Series H - Problem with Video

    Do you have this document?
  24. Replies
    37
    Views
    794

    Re: Partner 1 Series H - Problem with Video

    looks like your tool change may be holding it up you need to take picture with the tool call out on the right showing what tool is being called did you load the 20 pocket tc\ file i sent you and set...
  25. Replies
    37
    Views
    794

    Re: Partner 1 Series H CSM 09000 files

    The floppy on mill doesn't work or issues with reading on newer computer? I used to format floppy's on mill and then read and some times write to usb floppy drive on laptop. I have both my...
Results 1 to 25 of 118
Page 1 of 5 1 2 3 4