584,798 active members*
4,208 visitors online*
Register for free
Login

Search:

Type: Posts; User: CNCFanatiker

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. I can try it...when I'm experienced in this...

    I can try it...when I'm experienced in this control ...
    Which control is installed exactly on this machine? - (type, version)
    ... hope you get parameters...
  2. Hello purnananda, first at all welcome in our...

    Hello purnananda,

    first at all welcome in our forums on cnc-arena.com :)

    How did you delete all the parameters? :0 - Regulary someone with the same machine (also same type) could help.
    -...
  3. Hello arenamember, make sure that the same...

    Hello arenamember,

    make sure that the same tool table as well as in automatic mode also is activated in simulation.
    (look for status "M" & "S" of tool.t in the programm management)
  4. Replies
    3
    Views
    6,021

    Wehre do you've saved the program? - Only when...

    Wehre do you've saved the program? - Only when it's saved on other local hard drive - necessarily not in TNC:\ path then you should open it without any problems.
    Oherwise the file is saved in a...
  5. Replies
    3
    Views
    6,021

    Hello arenamember, are you sure that you've...

    Hello arenamember,

    are you sure that you've correctly saved your HEIDENHAIN programs from program management of programming station software?
    For better comprehension please upload the problem...
  6. Replies
    3
    Views
    2,190

    Hello arenamember, threading cycles you'll...

    Hello arenamember,

    threading cycles you'll find on second softkey bar:
    [attachment=12790:Threading_Softkeys.jpg]
    Click on second stripe in line. When it's active it changes to blue...
  7. Replies
    5
    Views
    2,616

    a pity. :wacko: Can you take a photo of the...

    a pity. :wacko:

    Can you take a photo of the laptop keyboard?

    Othewise take a look at the programming station / keyboard settings. Try to switch the default setting and restart the software....
  8. Replies
    5
    Views
    2,616

    No problem, but indeed curiously. Perhaps...

    No problem,

    but indeed curiously.
    Perhaps your laptop keyboard has a system specific dual key assignment? - ... but I've an idea to test for -> use the Windows on-screen keyboard.
  9. Hello arenamember, where exactly was the...

    Hello arenamember,

    where exactly was the problem? -> .. learning effect :)
  10. Hello, Do you still have these Problems? I...

    Hello,

    Do you still have these Problems?
    I think the hosts file schould not be the problem.
    At least Windows 8 on my system run's best so far... but I think without any system tuning Windows 8...
  11. Replies
    5
    Views
    2,616

    Hello arenamember, if you've an english / us ...

    Hello arenamember,

    if you've an english / us keyboard layout use your hardware keyboard.
    For semicolon on german keyboards use the Ö - key

    In the installation zip archive you'll find a...
  12. Replies
    2
    Views
    1,531

    Hello arenamember, specifically for the demo...

    Hello arenamember,

    specifically for the demo version there is no documentation. But with the Installation zip archive you'll get also "Operating Instructions for Programming Station" -> looking...
  13. Hello arenamember, do you've have any errors...

    Hello arenamember,

    do you've have any errors or errror messages until it blocks? Can you describe more detailed? :???:
  14. yes vista is a generally problem :D - windows7...

    yes vista is a generally problem :D - windows7 runs much better & windows8 is highly enjoyable

    If problems occurred during the installation, it is better you turn off the firewall... when it runs...
  15. Replies
    5
    Views
    2,604

    activating the virtual keyboard: - open the iTNC...

    activating the virtual keyboard:
    - open the iTNC Control Panel (green icon in your taskbar)
    - click the button "keyboard" (unique activation)
    - choose the option "Launch keypad at startup" to...
  16. Hello arenamember, the trick I've given to...

    Hello arenamember,

    the trick I've given to you...


    The only main differences ->
    The demo version of the iTNC 530 programming station permits you to save up to 100 NC blocks per NC program....
  17. Replies
    5
    Views
    2,604

    Hello arenamember good choice for your name ...

    Hello arenamember

    good choice for your name :thumbs: -> Welcome @ CNC-Arena!


    I would also advise you first to use the programming station demo version, - hundrets to thousend of cnc-arena...
  18. Replies
    1
    Views
    1,566

    Hello nero81, first at all - welcome at...

    Hello nero81,

    first at all - welcome at CNC-Arena forums!


    It's difficulty to imagine based on this description.
    Can you post here a sketch of it?
  19. Replies
    1
    Views
    2,050

    Hello sgmttsb, welcome @ CNC-Arena When...

    Hello sgmttsb,

    welcome @ CNC-Arena


    When exactly does the error message occur?
  20. Replies
    2
    Views
    7,745

    Hello cncuser1, first at all welcome in the...

    Hello cncuser1,

    first at all welcome in the forums of CNC-Arena!

    Do you use this editor itself? Is it only for g-code based programming languages? Allows the editor to programm cycle based...
  21. Replies
    1
    Views
    6,091

    Hello vimaro, welcome at the cnc-arena :) ...

    Hello vimaro,

    welcome at the cnc-arena :)

    It seems as if the boot sector of your hard disk is damaged or is not correctly initialized.
    You should contact the HURCO support and possibly save...
  22. Replies
    6
    Views
    11,276

    Hello FIELDSJJ, first at all - welcome @...

    Hello FIELDSJJ,

    first at all - welcome @ CNC-Arena :)


    What are you looking for in detail ? The file explains what functions any of the machine constants have ...
  23. Replies
    2
    Views
    2,695

    If I were in your position I would wonder if the...

    If I were in your position I would wonder if the afford it justified –maybe you can charge a fee as the customer has not given you the necessary file?!
    If you want accurate parts in the end, then...
  24. Replies
    1
    Views
    3,088

    Hello Welcome in the CNC Arena and happy Easter!...

    Hello
    Welcome in the CNC Arena and happy Easter! :thumbs:
    The error message indicates that you calculate the tool number over the parameter. Is that correct?
    Allowed area would be between 0...
  25. Replies
    2
    Views
    2,204

    Hello Why do you change the machine zero point...

    Hello
    Why do you change the machine zero point when you have done that before?
    Use the softkey “insert row/word” (2.soft keybar) :wacko:


    You can simplify the whole thing when you do it...
  26. Replies
    1
    Views
    1,737

    Hello Konstro The usage of the cutting data...

    Hello Konstro

    The usage of the cutting data table is usually prepared by the machine manufacturer.
    (only if you have any problems with the creation during the guarantee period!)

    However if...
  27. Replies
    2
    Views
    1,537

    Hello Welcome to the arena from me too! Do...

    Hello
    Welcome to the arena from me too!

    Do you get any error messages and do you also have the problem with already existing (old) programs?

    If it's a incorrectly defined BLK form then, as...
  28. Replies
    2
    Views
    1,823

    Hello luis Can you post a sketch to make it a...

    Hello luis
    Can you post a sketch to make it a bit clearer?
    As long as the rotations are situated in the working plane it’s possible. So multi-axis machining where the working plane is swivelled...
  29. Replies
    3
    Views
    3,944

    Hello hunt3r Write a bit more detailed when...

    Hello hunt3r

    Write a bit more detailed when the message comes up- when starting the machine? (that would be normal)

    To avoid misunderstanding, do you really mean 101 or I01? (with I for...
  30. Replies
    4
    Views
    3,462

    Hello dodo3 What’s included in your backup? As...

    Hello dodo3
    What’s included in your backup? As cgTNC already wrote, you need more than just a back up of the system files. An update of the complete PLC would be optimal

    However an interesting...
Results 1 to 30 of 190
Page 1 of 7 1 2 3 4