Both tables has the same code motors? You need to check the serial code servo motor before connect it!!! Look these pictures from my motor.
Enviado desde mi GT-I9300 mediante Tapatalk
Type: Posts; User: rgdcncmachines
Both tables has the same code motors? You need to check the serial code servo motor before connect it!!! Look these pictures from my motor.
Enviado desde mi GT-I9300 mediante Tapatalk
My Fanuc is OMD
Enviado desde mi GT-I9300 mediante Tapatalk
Fanuc OM use Alpha series motors. My 4th axis servo motor is A06B0123H0679 is an Alpha 3.
Enviado desde mi GT-I9300 mediante Tapatalk
The servo motor need be the correct serial code for Fanuc OM code is A06B 0123 H*** where last 3 numbers depend of the type of shaft motor.
Enviado desde mi GT-I9300 mediante Tapatalk
Here i send you some pictures. Also i have all parameters if someone need. PM please.
Enviado desde mi GT-I9300 mediante Tapatalk
Yes change the parameter 19.1=0 and probe it. Good luck
Enviado desde mi GT-I9300 mediante Tapatalk
Some parameters needs change to work with 4th axis. I can help you send me pictures of your servo motor and your axys drivers.
Enviado desde mi GT-I9300 mediante Tapatalk
Do you have all ready in the machine for the 4th axis??? You need an additional 4th axis servo amplifier, cables etc.
Enviado desde mi GT-I9300 mediante Tapatalk
Do you have the 25 pin pc to 50 ribbon cable wire connection or diagram?? can you help me with this?? i hope your comments.
Rick
Tano send me some pictures from your servo amplifier and control may be can help you with this work.
Enviado desde mi GT-I9300 mediante Tapatalk
My 4th axys its ready and work !!! But i need some parameters to the DMR, my gear ratio is 1/90.
Enviado desde mi GT-I9300 mediante Tapatalk
414 its for X axys check the servo cable in my control is JF1
Enviado desde mi GT-I9300 mediante Tapatalk
Yes
Enviado desde mi GT-I9300 mediante Tapatalk
Check your cable from driver to servo motor thats the problem.
Sent from my iPad using Tapatalk - now Free
Check your servo cables from drivers to servo motors.
Sent from my iPad using Tapatalk - now Free
Somebody can send me the parameters for 4th axys !!! Pleaseeeeee
Enviado desde mi GT-I9300 mediante Tapatalk
I need heeeeellllp!!!!
Enviado desde mi GT-I9300 mediante Tapatalk
We check all boards and components are very fine. Voltage AC 223V, voltage DC 307 VDC. all between range. But the alarm 444 again display in the machine in power on.
Enviado desde mi GT-I9300...
Yes PM me
Enviado desde mi GT-I9300 usando Tapatalk
I mean type B
Enviado desde mi GT-I9300 usando Tapatalk
Yes me too
Enviado desde mi GT-I9300 usando Tapatalk
My measure its 305 VDC
Enviado desde mi GT-I9300 usando Tapatalk
Fanuc service says the DC Link voltage must be between 370 to 400 VDC .
Enviado desde mi GT-I9300 usando Tapatalk
When i do turn to the motor i look in my position screen that B coordinates changing so the encoder its fine
Enviado desde mi GT-I9300 usando Tapatalk
Ill try tomorrow changing the cables for DC link because the alarm is only for the 4th axys
Enviado desde mi GT-I9300 usando Tapatalk
I change the cable
Enviado desde mi GT-I9300 usando Tapatalk
With the X axys cable
Enviado desde mi GT-I9300 usando Tapatalk
Yes i did and the same alarm 444 DGN bit#6 LV
Enviado desde mi GT-I9300 usando Tapatalk
My SVM is not FSSB interface
Enviado desde mi GT-I9300 usando Tapatalk
Thanks my friend let me see this attch.
Enviado desde mi GT-I9300 usando Tapatalk