584,829 active members*
5,144 visitors online*
Register for free
Login

Search:

Type: Posts; User: Tedger

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    152

    Re: VH65 BOLT PATTERN

    The center locating bore is 1.625" at .25 deep.
    Bolt circle options are;
    1/4-20 on 2.345 b.c. 4 pls.
    3/8-16 on 4.125 b.c. 4 pls.
    1/4-20 on 5.34 b.c. 6 pls.
  2. Replies
    4
    Views
    350

    Re: Drawbar piston O ring

    I have a spare along with the plate if your having trouble getting parts
  3. Replies
    4
    Views
    350

    Re: Drawbar piston O ring

    Whoops. Thats for the auger on a slant.Size 263 looks closest to me.
  4. Replies
    4
    Views
    350

    Re: Drawbar piston O ring

    The trade size is 247.
    .139 CS x 4.609 ID. Fadal part # is HDW-0170.
  5. Replies
    2
    Views
    417

    Re: Do I have a bad Amplifier

    The three gold amplifiers (AMP-0029) are AC power for the x,y and Z axis. Notice the labeling on the encoder cables for which is which.They are interchangable so try swapping two of them to see if...
  6. Replies
    1
    Views
    1,006

    Re: Hyundai Hit-20m turret problem!

    I just saw this post so maybe you figured it out. Your turret did not clamp and you'll need to manually clamp it our use the procedure in the Duplomatic manual. The thermal overload alarm is bogus...
  7. Re: Problem moving servo coolant from A-axis to B-axis on a Fadal

    Yup. Didn't make a difference. I'm going to move the A Axis and then try the Servo coolant in B with a different board later.
    Thanks
  8. Problem moving servo coolant from A-axis to B-axis on a Fadal

    I have a 4525 with the Servo coolant set up as the A-axis. I will be installoing a 4th axis Rotory in the A-axis slot so I wanted to move the servo colant to the B-axis. This machine is a 2003 and...
  9. Replies
    6
    Views
    2,821

    Re: Cant set tools Hyundai HIT 8s 840C

    I have Hyundai lathes with Siemens 840D control and have never ran the 840C control. On 840D, there is a button that togles back and forth between MCS and WCS. Have you tried pausing the program and...
  10. Replies
    4
    Views
    1,148

    Re: Tool Not Releasing

    See attached for Bellville info
  11. Replies
    4
    Views
    1,148

    Re: Tool Not Releasing

    There is rectangular aluminum plate that is attached to the pin that pushes down on the drawbar. The Plate is actually the moving part (Piston) of the air cyclinder. I have had these crack and leak...
  12. Thread: Vmc 15xt

    by Tedger
    Replies
    3
    Views
    1,520

    Re: Vmc 15xt

    Check your parameters. Type "SETP" and scroll through the options on travel
  13. Thread: CL access code

    by Tedger
    Replies
    4
    Views
    959

    Re: CL access code

    Perhaps yor parameters are wrong. Can you type "SETP" at the command line to double check them?
  14. Replies
    5
    Views
    1,013

    Re: Smoke after Spindle turn off

    Yes. The low air pressure most likely caused your problem. You now have a burnt spot on the low speed belt that will cause vibration and noise. It should probably be replaced.
  15. Replies
    8
    Views
    1,143

    Re: 4th Axis Inhibit wiring

    Go to "FADALCNC.COM" click on "Technical docs". In the lower left you'll see the Header for Wiring diagrams. Click on 4th axis servo options. Page 5 shows you the wiring diagram for the inhibit...
  16. Thread: Jump lines

    by Tedger
    Replies
    3
    Views
    1,339

    Re: Jump lines

    You are correct. You cannot use "R" as a label. You need to use "L" to designate how many time to repeat sub
  17. Thread: Hello everyone

    by Tedger
    Replies
    3
    Views
    908

    Re: Hello everyone

    Will this Help?
  18. Replies
    5
    Views
    1,100

    Re: Fadal VFD Choice ??????

    AMC will repair it if it's not to old. Give them a call
  19. Thread: X axis fault

    by Tedger
    Replies
    7
    Views
    2,954

    Re: X axis fault

    I've never blown the fuse on the amplifier.If your blowing a 20 amp fuse, I wouldn't suspect the control board. Either something in that amp is bad or maybe you have a short in the motor or a short...
  20. Thread: X axis fault

    by Tedger
    Replies
    7
    Views
    2,954

    Re: X axis fault

    The Axis control cards are the ones in the slots 9,10 and 11. The picture you have shows the axis Amplifier. There is one for each axis. The control cards rarely fail in my experiance. That means you...
  21. Replies
    26
    Views
    4,212

    Re: Digitizing a head port

    "I am using A 2008 haas vf3 with a 2 axis trunion table. We probe ports, chambers ect in 5 axis mode, using master cam to drive the probe . I had a custom post that was writting for my application by...
  22. Replies
    7
    Views
    1,331

    Re: Fadal VMC 15XT z axis move by hand

    7/16" - If you drop the way cover, make sure you clean out all the chips packed in the bottom.
  23. Replies
    7
    Views
    1,331

    Re: Fadal VMC 15XT z axis move by hand

    Yes, If you can get to it. It might be easier to remove the 4 bolts holding the Z motor on and rotating the coupling to lower the head. Use a sharpie to mark how the motor clocks to the ball screw or...
  24. Thread: vmc15xt issues

    by Tedger
    Replies
    14
    Views
    1,964

    Re: vmc15xt issues

    There are places that can test and repair your old drive. may be more cost effective if you have the time.
  25. Replies
    4
    Views
    1,088

    Re: VMC 4020 Z-axis brake

    You say you just bought it. Check the counter weight in the back for a shipping pin. These were installed to keep the weight from moving around. Should be about an inch or more in diameter and held...
  26. Replies
    1
    Views
    734

    Re: VMC15 Spindle Air

    Never saw spindle air on a little VMC15, But all the ones I saw were 7500 rpm. It looks like they relocated the Tool changer regulator to right under the valve.
  27. Replies
    4
    Views
    1,419

    Re: 1400-5A vs 1400-5C CPU board

    Well,I looked it up and you are correct. You can only use PCB-0041(384K) on the 5A .

    For the price people are charging for additional memory expansion. I would much rather purchase a calmotion.
  28. Replies
    4
    Views
    1,419

    Re: 1400-5A vs 1400-5C CPU board

    I have a 1400-5A with 4MB expansion. I never heard that the memory wouldn't work with the different revision letters. As long as it's a 1400-5, you should be good to go.
    Here's a compatibility...
  29. Replies
    12
    Views
    2,379

    Re: Good Buy Fadal VMC40

    That's a good price for a machine that was rebuilt 3 years ago. Especially if you get some good tooling with it. Fadal's are not very fast but they are pretty reliable and cheap to repair when the...
  30. Replies
    4
    Views
    1,241

    Re: Fadal 4525 any good?

    No. It has the Fadal 88HS control
Results 1 to 30 of 104
Page 1 of 4 1 2 3 4