Hello,
Wondering if there was ever offline programming software for the Torq-Cut 4 with BPC-MC. I suppose I can get into Fusion 360 if needed, but figured I'd see if there was something OEM...
Type: Posts; User: ralph@nes
Hello,
Wondering if there was ever offline programming software for the Torq-Cut 4 with BPC-MC. I suppose I can get into Fusion 360 if needed, but figured I'd see if there was something OEM...
I ran it a bit back when it was still up and running - it seemed to be 'ok' at best. I recall losing home position and having to re-zero my part every time there was a power failure.
Does...
This Millport was new from the factory with the Dynapath 20 control (3 axis with SEM motors and Heidenhain encoders). Fairly low hours when we shuttered it to make room for a new Haas - it had been...
Still looking?
nlh - post me an email address that can handle 30mb and I'll send them.
Couldn't reply but I got it. Thank you.
I don't know if you've already made a move yet or not, but we do lots of hard turning on Path I and Path II machines. Shaftwork mostly.
I'm not going to lie, you definitely deal with taper,...
It's very intuitive once you get past the 'It isn't G-code' and 'It isn't a Mazak either'. It requires a bit of a shift in programming thinking, but they program like a breeze and, to be honest, are...
This may be a bit late, but really any DOS 6.2 boot disk will work. A quick google will find that for you.
Will,
It won't let me PM you. I'm definitely in need of those manuals. Thanks much.
Feature not available. Pfft.
Will do. Thanks.
Hello all,
Have a need to do some internal broaching. I've got a spindle lock setup for the VF-2 mill that could be used, but I'm evaluating using the lathe to avoid an extra setup.
This is...
Hello all,
I have here a malfunctioning KO Lee Scepter with a NUM controller and drives. This unit has been painful to deal with the entire time we've had it, and recently has stopped some...
Hello,
Our trusty VF-2 is acting up. Our Y-Axis, when left uncommanded, will drift. If an indicator is placed on the axis, once the machine is warm it will move some amount, back off a little,...
Hello all,
I have a Mazak Tech here right now and we are trying to suss out the source of my 221 alarms (Turret clamp sensor malfunction).
The nature of the product line requires a somewhat...
Hello all,
I have a Studer S40-12 grinder here, equipped with a Sinumerik S3G control and 1HU 3056 motors. One of my motors is at the local repair house, they're unable to locate brushes through...
I would imagine this has to be an Analog system. Then again, I can't swear to it. My knowledge on the subject is limited.
I believe our maintenance guy cleaned the scale; We had the entire axis...
Al,
We've dug farther into this.
We've completely disassembled the axis and verified that the mechanical aspect of things are correct.
We've swapped the drives and servos and this exhibits...
I actually know the rebuilder pretty well. I seem to remember them not remembering the machine much when I talked to them last. I'll give that a shot.
Apparently I'm going to need some sort of 1747 module to talk to this thing. I spoke with a AB tech that said it could be as simple as an accidentally changed baud rate, or it could be a failing PV....
Looks like I've just got RS232 on the 5/03 connected directly to the panelview 550 (2711-K5A9). I can't 'see' any device in between the two. If there was a device, what would it look like and where...
No, there's nothing hooked to this that wasn't there yesterday or ever. I don't even see a place for a Cat5 cable.
For what it's worth:
SLC 5/03 CPU module
1 SLC servo module with Ultra...
I'm not trying to connect with any sort of software, this error comes up on the front display when we start the machine up.
Al, the two LED's that indicate network connectivity are blinking, the...
Help!
I've got an old Heald grinder that's been set up with one of these. It's worked flawlessly for quite some time, we powered it up this morning and got a 'No active nodes found on the...
Figured I would chime in and add that this is the parameter for the 640T Fusion control as well. I just used it on my '99 QT250HP.
Thank heavens for this post, and google.
A note, if you have to go that far and it's not obviously a cable or something, the set screw is under the encoder. It's a pain to see and get to.
You are not going to believe this. I still don't.
The set screw that tightens the encoder collar onto the motor shaft broke in half. The motor was spinning away wildly and the encoder was pretty...
For anyone who ends up with this problem or similar:
SKBIF card AND Video card. Problem solved.
http://www.cnczone.com/forums/showthread.php?t=68710