[jamessiffel]

Hello! Any and all for a Mynx please! If you need to, private message me! Thanks a million!

[dhardt]

"Mynx" is an entire series, and has been made for many years. Designs and functions have changed over the years, as well.

I will attach the most popular ones...

[dhardt]

Mynx 650 Service manuals for Installation...

[dhardt]

Mynx 650 Service manual for Mechanical...

[dhardt]

Mynx 650 Service manual for Alarms/Electrical...

[dhardt]

Mynx 6500 Service manual for Mechanical...

[dhardt]

Mynx 6500 Service manual for Alarms/Electrical...

[colton_m]

Would you happen to have a manual, or section of one, that describes in detail how to align the headstock, turret and tailstock?
Also specifically how to reset the center-line after preforming such an alignment?

Model: Lynx 220 LC
Year: 2011 – Sept.
Serial#: ML0022-005385

Thanks,
Colton.

[dhardt]

This Lynx 220 installation manual has the geometry adjustments near the end.

[CPInc]

Excellent information ! Do you have the same manual for a Lynx 220 LSYC ?

Thank you.

[dhardt]

CPInc,

While it would, eventually, be beneficial to have a version for every style of each machine, we are in our infancy with regards to our documentation.
Our focus, currently, is on getting versions of service manuals that were do not have.

Someday we might be caught up enough to have manuals specific to individual product, and not limited to its base version.

If you have specific sections that you would like that deal with the sub-spindle or Y-axis geometry, I might be able to find comparable sections from other model's manuals.

[CPInc]

Thanks for checking it out, I know the "Y" axis Lynx is a newer release for Doosan. Currently I am not having any issues with the machine, I just like to have the information if something does go wrong. I appreciate you getting back to me.

[dhardt]

Anytime.

If you have any questions, you may call Doosan Service 24/7 at 888-936-6726 (888)-9-DOOSAN

Or dial directly to my extension 8:30-5:30 Easterntime at 973-618-2461

...or call my cell 24/7 at 973-803-9479

Let me know if we may be of service.

[dhardt]

A manual for Teardown and rebuild of a Puma 240MS

Not sections of this manual can be used for other slant-bed models
i.e. The live tooling in this manual is "rear-mount" ...as are the early TT1800's and 2500's, TL2500's Puma 2500, others...

[mavruk]

We have a Puma 2014 400 M with a Fanuc I-series and a 2014 lynx 300M. Do you have service instructions for spindle and turret alignment. also do you have parameters for the turret position so I can realign the x-axis to the proper position. Currently the only way I know to realign the turret is to bring the x to zero and adjust until its in the proper position then home it then bring it down the amount it was off, And finally I would turn parameter 1815 APZ from 1 to 0 then back to 1 and restart. This works but it constantly changes my home position.

[dhardt]

We have a Puma 2014 400 M with a Fanuc I-series and a 2014 lynx 300M. Do you have service instructions for spindle and turret alignment. also do you have parameters for the turret position so I can realign the x-axis to the proper position. Currently the only way I know to realign the turret is to bring the x to zero and adjust until its in the proper position then home it then bring it down the amount it was off, And finally I would turn parameter 1815 APZ from 1 to 0 then back to 1 and restart. This works but it constantly changes my home position.

The 400M and 300M (both having milling) align in the same way as the 240M(S)

To align the spindle and turret, you should be able to use the 240MS manual and instructions that are here, in combination with section 5 (or E, depending if the sections are numbered or lettered) of the Instruction Manual that shipped with the machine.

Start by checking the Main Spindle for taper, then the Sub spindle (or tailstock, if applicable)

Check that they center-match to within 0.0002" or less.

Align all three planes of the turret to square and position.

Then set home by centering X at spindle center (<0.0002") and, using relative position reset, move X up to the amount in parameter 1240, and then setting 1815.4 1->0->1

If you have put your X-axis 0 back onto the spindle's centerline, then the home position alteration should not matter as home is STILL the 1240 position from centerline.

[dhardt]

DNM500 Maintenance Manual

[marcelo_maint]

I would appreciate it immensely make available machining center files HP4000,
I am of the maintenance area and I have great difficulty in solving problems of these machines

[dhardt]

I would appreciate it immensely make available machining center files HP4000,
I am of the maintenance area and I have great difficulty in solving problems of these machines

I will post any relevant files upon my return to the office,on Tuesday.

[marcelo_maint]

THANK YOU VERY MUCH