I just purchased a Charmilles Robofil 200. Just now powered it up. I receive a message on screen that says 'EOB P20?'. Anyone no what this means?
I just purchased a Charmilles Robofil 200. Just now powered it up. I receive a message on screen that says 'EOB P20?'. Anyone no what this means?
Check your incoming power. Make sure that yor internal transformers are set to the same as your 3 phase. You cannot have no more that 3 % difrence between leggs R-S-T and no more than 4% diffrence from your incoming to your xformers taps inside the generator.
OK.
So if your 3 phase is 400 vac, make sure that the taps on theinternal transformers are also set for 400vac. I believe you have 4 xformers on that 100 series machine.
ok.
alex
Ok, after checking the power and setting the transformers. We have a machine powered up. Replaced the batteries. Now the system software stays put after cycling the power. Now if my manuals would just show up, I might be able to get started on a job.
Hello all, I'm new in this post, and I have many questions for a use a machene wire edm charmilles robofile200, I see some commets but none favors me,I hope some of you can help.
I work in Cd Juarez Chihuahua Mexico, and in the factory when I work, we have a machine that don't work arround 2 years ago, I try to work in this machine but I see the format to read a program is diferent to sodick wire, I have Bobcad-cam for a make programs to sodick machine, but the charmilles wire don't read the program.
My first questions in, How to I do for a make program in language for this machine?.
How to I see in the screen of the machine?
What is the programs can I use for a program the machine?
Thanks,,,,,,,
I have a robofil 100 machine but lost 852478 ccu exe board .so i need 978081,978583 program on 852478.can you help me ?you shoud use programmer download 978081 and 978583 program and email to me.thanks!i am chinese ,come from shenzhen city.
http://us.gfac.com/service/parts/cat...tos/852478.JPG
Good Day,
I am sorry to report that my machine is in constant production at this time and can not be stopped to download the program. Please contact Charmilles they have been exceedingly helpful with every problem we have encountered.
Thanks,but chanmilles in china ,not supply this service(because robofil 100,200,400 in china is very few) .can you ask them and email program to me ?thank you very much!my email:[email protected]
Hello all,
I am new to this forum and I am relatively new to WEDM.
I bought a robofil 200 from farance, it came with the software "by mail".
Couldn't check the machine until yesterday because of the electricity supplier.
The machine starts but I can not load the software.
I dont't know why...disk drive seems good...the software may be bad...I am out of options..
Spent all night formating disks and all I get is
Chargement#ILC Ereurre Format
Any ideeas?
Does any body have the original disks?
Please help!!!!
i don't know much your machine ,your machine maybe system board erreur like me. you should confirm system board model:852477 ccu pil (program:978082,978202,978203,978204,978205,978206 ),852478 ccu exe(program978081,978583(?)that i lost this board),852479 ccu cof(program 978175).if there board are right,you should check logic circuit.good luck! your system disks are no error.
if you have programmer,please download 852478 ccu exe program(978081,978583)email to me .thank you.
Dear friend
you do not need original disk
first buy 2 floppy disks
then you must format that disks by other charmiils machine or (you can format the disks by Pc but you must format those in 720kb).
then copy softwear in one of the Disk and copy tecnology files to second floppy disk
at the first insert the softwear disk in DD1 or DD2 restart the machin and charge it.
aftre around 14min your machine will start up.
after startup inset second disk and copy wire and other technology file in machine.
by the way after format the floppy you need to read that by PC but computer shows you an error about not read this format becuse format is 720kb for this problem you must fill 2 square hole in disk as lock by something.
have a good time.
Thank you for your info.
The problem is I do not have the right software to copy on the disks.
Can anybody help me with the software?
Hello to all, i have a charmille robofill 100 and i have the error chargement#cks erreur format when i insert communication floppy and press charger. Any solution? thanks to all
hello bigodino,
I have a charmilles robofil 400. I have the same problem with booting. When I insert the communication floppy and press charger the same error occurs
“ chargement#cks erreur format
Did you solve the problem?
thank you in advance for reply
Hi. I need some help. The company where I work bought 2 Robofil 200. Both are with dead batteries, so need to load firmware.
Original Software disks are very bad, but it was possible to read 3 of them except AutoDiagnostic disk. There was 1 working (i'm not sure by 100%) among 4 floppy drive. I tried to load Communication Disk, floppy lights on about 1-2 sec then the text appears on the screen:
Chargement#ILC Ereurre Format
I have read this topic and other topics like this. I'm sure that original Communication Disk was overwritten (see it by Disk Editor and DOS with native languages is in sector 1 of track 0). I don't have another Robofil to format 720k floppy and, to found a very old PC is the same difficult. Formatting by modern PC even by DOS on Celeron 333 PC was not successful (I know that formatting is 720k, 80 track, 9 sectors and to close a square hole in 1.44 disk) . The same #ILC erreur format. I tried to connect Robofil floppy drive to PC but it didn't work. How can I plug and test it?
Update... 2 of the disks are originally formatted, so I decide to copy main file FH44.bx8 to one of them. And... Nothing. The same situation. #ILC error. There are two variants: 1. need original Charmilles Communication disk or 2. Floppy Drive is not working fine.
I read that new2edm just formats a disk by Charmilles machine and copy files to it and it's working. One way out remains: FDD. The problem is that I don't know how to test it. I tried to connect it to 286 with ISA-multicard (HDD+FDD+Ports) today. The drive is spinning, LED is lighting, DOS boot disk is in the drive, but DOS said Drive NOT Ready. Give me a pair of advices, please.
hello
you do not need to clean the liner encoder !!! it's not safe work you want to do.
Just do this work:
1-go on Setup page.
2-go on Refrence page.
in Reference page you will see 5 axis X-Y-Z-U-V
your U and V axis alarmed with a star single near each axis that lose Refrence
just move u axis to end and go back very slow do this work for V axis, star single will not see and your machine will work correct.[/QUOTE]
Hello to everyone, I have a problem with my Charmilles Robofil 2000, when I turn it on I get massage "Going to sleep mode".
Anyone Help?
I have loaded firmware at last, connected BOOT SECTOR of Charmilles Techno disk and firmware file (FH44.bx8) with Disk Editor software. There are the nuances:
1. 720k floppy must be formatted on the same type of Robofil (100,200,400,600 or the same Roboform). Any PC, any DOS version formatting = #ILC erreur format. Only Robofil writes the necessary BOOT SECTOR.
2. Firmware file (with .bx8) must be the first in the FAT table on floppy.
hi i need POCKET GUIDE ROBOFIL OPERATOR charmille 200 in french language thank you
Hello to everyone, I have a problem with my Charmilles Robofil 2000, when I turn it on I get massage "Going to sleep mode".
Anyone Help?