584,841 active members*
4,285 visitors online*
Register for free
Login
IndustryArena Forum > MetalWorking Machines > Hitachi Seikis > Micon 16 hitachi Seiki Secos II - ladder save
Page 1 of 2 12
Results 1 to 20 of 21
  1. #1
    Join Date
    Aug 2007
    Posts
    138

    Micon 16 hitachi Seiki Secos II - ladder save

    Hi all.
    I have a Hitachi Seiki VK45 VMC. Since support is so limited on this machine, I try to take as many precautions as I can. I would like to back up my ladder program. I already have all the paremeters backed up but not the ladder it's self.

    I have the WinYumo (win yu yu) software and the correct serial cable plus this document:
    https://secure.filesanywhere.com/fs/...8661626fb3b26a

    shows how to put the ladder onto the mill. I need to get the ladder OFF so I can save it! Plus I have a friend who has lost his ladder and I would like to send him a copy of mine.

    Last thing in the world I want to do is hose mine trying to copy it

    I think, the PC side of the thing is fairly common. Here is a picture of my screen in the PC mode:


    Well the pic does not show so here is the link for it: https://secure.filesanywhere.com/fs/...6b8661657279a8
    it looks like this:
    ** M16-II Ver5.0 **







    F1 SEQUENCE F2 MACHINE F3 MONITOR F4 LADDER F5 ALARM F6 END


    I can figure out WinYumo, it's the mill I am worried about. If anyone knows the proceedure to get the mill to send the ladder to WinYumo I would sure love to know how. Also let me know what kinds of "stupd" things to watch out for so I don't hammer my "working" mill !!!!!!!

    Thank you
    Dan Clemens
    Summerville, Oregon

  2. #2
    Join Date
    Aug 2007
    Posts
    138
    Bump? anyone?

  3. #3
    Join Date
    Aug 2007
    Posts
    138

    I tried!

    I tried it! No luck!

    I connected the serial cable to the middle pc board (the one with the write enable switch on it)


    I set Win yu yu to 4800 baud, 8 bit, no parity and 2 stop bits. I then pressed "Free RX" it asked for a file name, I typed "my-ladder" pressed "save" Win yu yu said "Receive Data?" I pressed yes.

    on the mill, PC screen:


    I pressed F1 SEQUENCE -> F5 RS232 -> F4 BAUDRATE (ARROW TO 4800,INPUT KEY) -> F2 WRITE (ARROW TO 128,INPUT) , READ ADDRESS 0000, INPUT, says WRITE START, WRITE ENABLE SWITCH ON!

    The mill begins to send the ladder but the "framing error" shows up.

    Any one know how to correct this?

    Dan Clemens
    Summerville, Oregon

  4. #4
    Join Date
    Jan 2010
    Posts
    11

    Hitachi Seiki seicos LIII

    Dancy.
    could you share files again?

    Mike

  5. #5
    Join Date
    Dec 2007
    Posts
    5
    Anyone have a copy of yuyu etc they like to share?

    Thanks

  6. #6
    Join Date
    Aug 2007
    Posts
    138
    If anyone needs Winyumo (yuyu) here is a link to where I stored it at FilesAnywhere
    https://www.filesanywhere.com/fs/v.a...8e5c607477af6e

    If you get this to work, PLEASE send me details, as you can see from the above posts, I have not been able to back up my ladder, if I can get it off I will make it available to those of you that have lost yours.

    Dan

  7. #7
    Join Date
    Dec 2009
    Posts
    539

    Saving ladders

    hello all,

    I have been using this software for a while now. Please message me with your specific problem and machine/control and I am sure I can help you out. Also let me know if there are any errors you are getting as well.

    John

  8. #8
    Join Date
    Jan 2014
    Posts
    11

    Re: Micon 16 hitachi Seiki Secos II - ladder save

    Dear Sirs,
    I have a lathe Hitachi_Seiki_HT20S2 with SEICOS Computer and Micon M16-II ver 5.00 PC Board. I have lost PLC program. If a copy is available, could be much appreciated to send me. My mail is <[email protected]> Thanks
    KIAF
    Service engineer

  9. #9
    Join Date
    Dec 2009
    Posts
    539

    Re: Micon 16 hitachi Seiki Secos II - ladder save

    Hello,

    please check your email. I sent you a message,

    John

  10. #10
    Join Date
    Aug 2007
    Posts
    138

    Re: Micon 16 hitachi Seiki Secos II - ladder save

    I did later get this procedure to work....
    details here
    https://www.filesanywhere.com/fs/v.a...885a61727cb49a

  11. #11
    Hi Dancy,
    The link does not work, could you load it again, or could write down the steps which worked with you
    sting

  12. #12
    Hello

    I have some problem with my machine.

    Model is HC400 Hitachi seiki control fanuc 15MA.

    Main board is SEICOS M16-II .

  13. #13
    hello

  14. #14
    Dear Sirs,

    Model is HC400 Hitachi seiki control fanuc 15MA.

    I have a lathe Hitachi_Seiki_HC400_FANUC 15MA with SEICOS Micon M16-II ver 7.5** PC Board.
    I need Ladder.
    My mail is <[email protected]>
    Thanks

  15. #15
    Join Date
    May 2008
    Posts
    7

    Re: I tried!

    Hello,

    Does anyone have a copy of the software for communications with Seico controller on a Hitachi Seiki HC500 with fanuc 11M control?

    I have tried the links in this thread - they appear to no long be functional.

    Thanks,

    Jay Ostrander
    Absolute CNC Machinetools, LLC.

  16. #16
    Join Date
    Dec 2009
    Posts
    539

    Re: I tried!

    Jay

    sent you a PM

  17. #17
    Join Date
    Feb 2017
    Posts
    5

    Re: Micon 16 hitachi Seiki Secos II - ladder save

    Hello everyone, I need your help, step by step procedure to back up and installation of all Michon 16

  18. #18
    Join Date
    Aug 2007
    Posts
    138

    Re: Micon 16 hitachi Seiki Secos II - ladder save

    Boy, your right. \
    Dead links File share must have done some reorganization or something. Let's try some fresh links:
    WinYuMo and params: https://www.filesanywhere.com/fs/v.a...8c616271b8a6af
    "how I did it files": https://www.filesanywhere.com/fs/v.a...885a61727cb49a

    I think that is all I had posted
    Let me know if not working

  19. #19
    Join Date
    Jan 2021
    Posts
    13

    Re: Micon 16 hitachi Seiki Secos II - ladder save

    HI*I have a hitachi seiki vk45 vmc Ladder corrupted*and no backup and no softwarecan you please*help me([email protected])

    - - - Updated - - -

    HI yoni
    *I have a hitachi seiki vk45 vmc Ladder corrupted*and no backup and no softwarecan you please*help me([email protected])

  20. #20
    Join Date
    Aug 2021
    Posts
    10

    Re: Micon 16 hitachi Seiki Secos II - ladder save

    Hi Dan,
    Can you please share me the Winyumo (yuyu) software?
    My email: [email protected]
    Appreciation to your help!
    Bob

Page 1 of 2 12

Similar Threads

  1. Hitachi Seiki Pallet loader PL 400 Micon 16 electrial manuals
    By orchidlane in forum CNC (Mill / Lathe) Control Software (NC)
    Replies: 1
    Last Post: 12-16-2017, 10:31 AM
  2. Hitachi Seiki HG500 Fanuc 15M Micon 16 II
    By cevyil in forum CNC (Mill / Lathe) Control Software (NC)
    Replies: 1
    Last Post: 06-09-2012, 07:12 PM
  3. Hitachi Seiki Micon 16-II
    By oldgoat in forum CNC (Mill / Lathe) Control Software (NC)
    Replies: 1
    Last Post: 03-30-2012, 12:24 AM
  4. Ladder for Hitachi Seiki HT-15
    By stump1189 in forum CNC (Mill / Lathe) Control Software (NC)
    Replies: 0
    Last Post: 11-10-2011, 12:56 AM
  5. hitachi seiki with Fanuc 6MB and Micon 16
    By F.Sharifi in forum Fanuc
    Replies: 2
    Last Post: 06-30-2010, 12:13 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •