541,770 active members*
3,429 visitors online*
Register for free
Login
IndustryArena Forum > CNC Electronics > Spindles / VFD > Huanyang Chinese VFD settings and manual here!
Page 38 of 38 28363738
Results 741 to 743 of 743
  1. #741

    Join Date
    Jan 2021
    Posts
    5

    Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by mactec54 View Post
    Yes, if you look through what I have posted here you will find the Parameter's you need to set for your spindle, or if you post the complete spindle motor spec's then I can post what Parameters you need to set
    Already read .. thank you mactec54 !

  2. #742

    Join Date
    Mar 2021
    Posts
    4

    Re: Huanyang Chinese VFD settings and manual here!

    I received my HY VFD a couple of days ago. It’s 2.2kw. I wanted to test as soon as possible since it will be couple of months before I complete my build. While Testing with a 2.2kw spindle I noticed that there was a motor spinning sound coming from spindle but collet nut was not spinning. I reset the vfd several times but problem persisted. Removed and reconnected wires on both sides a few times. After spending a couple of hours I decided to open the spindle from top. What I noticed was the numbers on aviation plugs were not matching with internal wiring. #4 pin was supposed to be earth or not connected but inside the spindle it was connected and pin #3 was not connected. Swapping the wires worked without any issue.

  3. #743
    Member
    Join Date
    Jan 2005
    Posts
    12236

    Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by Arjcnc View Post
    I received my HY VFD a couple of days ago. It’s 2.2kw. I wanted to test as soon as possible since it will be couple of months before I complete my build. While Testing with a 2.2kw spindle I noticed that there was a motor spinning sound coming from spindle but collet nut was not spinning. I reset the vfd several times but problem persisted. Removed and reconnected wires on both sides a few times. After spending a couple of hours I decided to open the spindle from top. What I noticed was the numbers on aviation plugs were not matching with internal wiring. #4 pin was supposed to be earth or not connected but inside the spindle it was connected and pin #3 was not connected. Swapping the wires worked without any issue.
    This is common that the Ground is not connected inside the spindle, you have to connect this, this is a first check everyone should do before connecting any power to the spindle, the 4th pin must be Grounded

    The correct wiring of the plugs are important when you here something like this with these spindles you have a phase missing or incorrectly wired
    Mactec54

  4. #744
    Member
    Join Date
    Mar 2021
    Posts
    2

    Question Re: Huanyang Chinese VFD settings and manual here!

    This thread is an asset to the internet and I'd like to thank Mactec54 for answering all these questions for so many years.

    I'm at a loss and nowhere else to turn so hopefully it's not too much of an imposition to ask about setting up a Hyunyang 7.5kw GT series to operate a 5hp 3 phase table saw. The settings are pretty basic according to numerous vids on youtube, but I'd like to mount the vfd on a wall away from the saw for a number of reasons. Is it possible to do this and add an on/off switch at the saw? Is there a way using the green terminals to program a remote on/off switch?


    If it isn't possible to locate the VFD remotely it seems wise to protect it from dust which in my mind means enclosing it and adding a fan and filters to remove heat. That adds another layer since there is no 12vdc power or even 120vac to power the fan at the saw unless I add that. The saw is on wheels by necessity as it must be stored in one area and used in another. so that means dragging power along with it.

  5. #745
    Member
    Join Date
    Jan 2005
    Posts
    12236

    Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by justbrowsingthrough View Post
    This thread is an asset to the internet and I'd like to thank Mactec54 for answering all these questions for so many years.

    I'm at a loss and nowhere else to turn so hopefully it's not too much of an imposition to ask about setting up a Hyunyang 7.5kw GT series to operate a 5hp 3 phase table saw. The settings are pretty basic according to numerous vids on youtube, but I'd like to mount the vfd on a wall away from the saw for a number of reasons. Is it possible to do this and add an on/off switch at the saw? Is there a way using the green terminals to program a remote on/off switch?


    If it isn't possible to locate the VFD remotely it seems wise to protect it from dust which in my mind means enclosing it and adding a fan and filters to remove heat. That adds another layer since there is no 12vdc power or even 120vac to power the fan at the saw unless I add that. The saw is on wheels by necessity as it must be stored in one area and used in another. so that means dragging power along with it.
    So are you going to mount the VFD in a Metal box /cabinet on the saw or mount it some where else, seeing that you have to move it would be best is to mount it on the saw, there is a relay in the VFD Drive that can be used to switch on a Fan, there are many ways to do this, if remote is what you really want to do then it can be done with careful planning

    If your saw motor is 50Hz /60Hz then most likely there won't be much to change for the Drive setup as by default VFD Drives are set for either a 50Hz or 60Hz motor depending in what country you live

    Remote On / Off it easy to do
    Mactec54

  6. #746
    Member
    Join Date
    Mar 2021
    Posts
    2

    Re: Huanyang Chinese VFD settings and manual here!

    Quote Originally Posted by mactec54 View Post
    So are you going to mount the VFD in a Metal box /cabinet on the saw or mount it some where else, seeing that you have to move it would be best is to mount it on the saw, there is a relay in the VFD Drive that can be used to switch on a Fan, there are many ways to do this, if remote is what you really want to do then it can be done with careful planning

    If your saw motor is 50Hz /60Hz then most likely there won't be much to change for the Drive setup as by default VFD Drives are set for either a 50Hz or 60Hz motor depending in what country you live

    Remote On / Off it easy to do
    I want to mount the VFD on a wall in a location it would not need the enclosure and I have 25' of heavy jacketed cabling to reach the saw. The motor is indeed 50/60hz and setup is pretty basic. There is a wealth of information online as to the settings for this application but I can't find any information about setting up the remote on/off.

    I'm glad to hear remote on/off is easy to do. How do I go about finding the information to set that up? I'd like to use something like a Woodstock D4151 which is just a basic switch but has a large paddle for emergency stop. When the switch is closed the vfd starts when its open it stops. I've read the manual and the answer seems close I just am not getting it.

Page 38 of 38 28363738

Similar Threads

  1. Car hoist 3phase settings on huanyang vfd
    By pietskiet in forum Spindles / VFD
    Replies: 1
    Last Post: 10-21-2019, 10:04 AM
  2. Replies: 4
    Last Post: 02-16-2017, 05:42 AM
  3. Huanyang SL-240EE Manual (SL Series Manual for Vector VFD)
    By Cogolith in forum Phase Converters
    Replies: 2
    Last Post: 05-24-2016, 04:19 AM
  4. Huanyang inverter PD settings
    By jamriggsy in forum Phase Converters
    Replies: 2
    Last Post: 03-15-2013, 04:54 PM
  5. Huanyang 2.2kw VFD, 0-10v 3600rpm settings?
    By EmeraldIsleforg in forum Phase Converters
    Replies: 1
    Last Post: 09-23-2012, 03:00 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •