Hi,
Do anyone know where i can find RexRoth Drivetop configuration software?
Thank you
Christer
Hi,
Do anyone know where i can find RexRoth Drivetop configuration software?
Thank you
Christer
It looks like they have pulled DriveTop off of their site. I downloaded DriveTop16V14 from their site December of last year. It's 50MB. I can't tell for sure, but it may be that IndraWorks Ds 09V12 has replaced it. You can find that at Bosch Rexroth Electric Drives and Controls That link should take you to a page with the Download link to the page with the file. Their website leaves me with a whole lot more questions than answers.
Hi Mike,
Yes it seems that they have pulled it off their site.
I have searched at many places without any hits that works.
Thank you very much for your help anyway, and i will also give IndraWorks a try.
Regards
Christer
What Drives you using? Drive Top 4v05 to be used for ecodrive 1, Drivetop 16 to be used for Ecodrive 3. Indra Works DS to be used for Indradrive CS. Indraworks is not designed for older drives....
Stephan
I HAVE SOME INDRAMAT ECO DRIVES (DKC01.1) AND CAN'T FIND THE SETUP
SOFTWARE ANYWARE.
ARE THESE DRIVES STILL SUPPORTED AS THEY DON'T LOOK THAT OLD?
WERE CAN I FIND SERVO MOTORS THAT WILL MATCH THESE TIPE OF 3PHASE
AC DRIVES?
REGARDS
DANIEL
@ Daniel,
For DKC01.1 you need Drive Top 4v05 or near this Version number. Motors, cable for these drives i can help. Please send me your email via pn.
Stephan
hello please, I need your help, i need the software drive top 4v05,
I need software drive top 4v05 for DKC11.3-040-7-FW DRIVE, can any body help me
I am not sure what onkel from germany said,but I have a cd with this software on it. if onkel did not fix u up let me know and I will figure how to cc for u.
Dear Friends , it is always useful to have old software, and I need Drive Top for working on a Indramat DKC02 drive.
Does anyone could help me on that ?
If someone could send me a CD with Drive Top I´d really be thankful.
Thanx - Valdir Bispo
HI EVERYONE.
I AM LOST BETWEEN I THINK 4 PEOPLE WHO IS TRYING TO MAIL ME A COPY
OF DRIVE TOP SOFTWARE FROM ALL OVER THE WORLD.
NOT ONE SEEMS TO GET IT RIGHT.
I AM NOT SHARP WITH COMPUTERS BUT IF I WANT TO MAIL A FILE I ATTACH IT TO MY MESSAGE AND MAIL IT.
THE MANUAL SAY IT IS ON TWO STIFFIES SO THE FILE CAN'T BE THAT BIG.
ANYWAY I AM LOSING HOPE OF EVER FINDING THIS.
REGARDS
DANIEL
Drive Top 16 was avaiable to download from Indramat website. Daniel needs DriveTop 4v05 witch has never been avaiable for free. DriveTop 12 and higher can not connect to DKC01.1
Greetings Stephan
Hello,
I would like to configure an ecodrive DKC02.1 so I need drivetop...
But wich version?
I don't find any version on indramat website...
Somebody can help me?
Many thanks!
You need Drive Top 4v05.
Greets OS
i Need Drive Top 4v05.
Dear Onkel Steven,
Thanks a lot for the Links.
The files are already downloaded to my PC thanx to U.
Urgent help!! I have a DKC21.3-100-705vrs-FM drive with the firmware FWA-ECODR3-FLP-05VRS-MS. Which software that I need to use in order to communicate with PC through RS232? Thanks
U need DriveTop 14 and higher. Avaiable from Bosch Rexroth Website
https://www.boschrexroth.com/various...jsp?oid=118749
Software is German and English
Greetings Stephan
I have a DKC1.1-030-3 indramat drive in an old system used for life testing. I am trying to repurpopse the drive and motor for a new fixture but cannot locate our copy of the drive top software. it seems that since it was on floppy it was tossed out during a move. We still have the cable installed on the drive from the last time it was used. Would anyone be able to forward me a copy of the software?
>>@ Daniel,
For DKC01.1 you need Drive Top 4v05 or near this Version number. Motors, cable for these drives i can help. Please send me your email via pn.
Stephan <<
thanks
grifftek AT grifftek dot com
Steven, thanks for your reply.
I've tried it before but this software seems like doesn't support the firmware in my Ecodrive03. Any solution?