584,802 active members*
4,949 visitors online*
Register for free
Login
IndustryArena Forum > Machine Controllers Software and Solutions > Fanuc > Looking for 27C64 Ladder chips Fanuc 0-A or B
Page 1 of 2 12
Results 1 to 20 of 32
  1. #1
    Join Date
    Apr 2009
    Posts
    108

    Looking for 27C64 Ladder chips Fanuc 0-A or B

    I'm looking to lay my hands on some ladder logic chips from a dead machine. I need to verify that my PC Writer from Fanuc will read, decode and burn new chips. The problem is that I don't have any chips to experiment with.

    The chips will have a part number silk screened onto them something like
    27C64-15. These were used on the old Fanuc 0 models A and B controls. The later model B and C controls used 27C256 chips. I have these.

    If I can get this to work, I plan to modify some ladders on a few grinders. I don't want to experiment on the only good chips I have.

  2. #2
    Join Date
    Jun 2010
    Posts
    161
    Check your PM

  3. #3

  4. #4
    Join Date
    Apr 2009
    Posts
    108
    Thanks for the info. I was trying to find some old chips that had already been programmed. It looks like my best bet is to program some new ones.

  5. #5
    Join Date
    Apr 2009
    Posts
    1379
    I probably have old programmed and new ones.
    How many?

  6. #6
    Join Date
    Apr 2009
    Posts
    108
    I just need one set to see if the PC Writer I have will work with the 27C64 chips. I have one set but when I try to decompile them I get a ROM parity error. I'm not sure if the problem is with the chips or the PC Writer I'm using. I can work with the 27C256 chips without a problem.

    I tried burning some blank chips but couldn't get these to work. It may be that the PC writer doesn't support the older chips. I noticed that the 256 LED comes on when I try to work with the 64 chips. I may be doing something wrong.

  7. #7
    What are you using to communicate to the PMC writer with? The old series 0-MA / 0-MB can not be done on a laptop. You need a Fanuc PG Mate.

  8. #8
    Join Date
    Apr 2009
    Posts
    108
    That could be the problem. I have been using a laptop for several years to modify the ladder on 0-C controls. This is my first shot at doing a 0-A control. I haven't seen a P-G Mate in many years.

    It looks like I may need to find another way to activate an M-code.

  9. #9
    I have a PG Mate emulator. It runs on XP. But I think you have to use a special EProm Reader/Writer NOT the Fanuc PMC writer. I have never used it but I can send you a copy. It is 3.25 MEG Zip file. It was designed just for what you are trying to do and it's free. Do you want a copy?

  10. #10
    Join Date
    May 2011
    Posts
    2
    Mr. drdos I would be interested to the PG mate emulator you could send me a copy?

    thanks

    menec from Italy

  11. #11
    Wow this PG Emulator is really getting popular. I have the web site that also has other things of interest too. Please check out all of dnc
    Hope this helps.

  12. #12
    Join Date
    Mar 2006
    Posts
    34
    Quote Originally Posted by Shoprag View Post
    That could be the problem. I have been using a laptop for several years to modify the ladder on 0-C controls. This is my first shot at doing a 0-A control. I haven't seen a P-G Mate in many years.

    It looks like I may need to find another way to activate an M-code.
    Hello, did you have any luck with the PMC emulator from drdos for the 0MA? Thx.

  13. #13
    Here it is

  14. #14
    Join Date
    Mar 2006
    Posts
    34
    Hello drdos, did you send the emulator? Nothing here, thx.

  15. #15
    Quote Originally Posted by davehall View Post
    Hello drdos, did you send the emulator? Nothing here, thx.
    Check your PM

  16. #16
    Join Date
    Sep 2011
    Posts
    8
    Hi,
    drdos: Please send me a copy of PG Mate emulator.
    Thank you!

  17. #17
    Join Date
    Jan 2012
    Posts
    0
    drdos i am wondering if I can get a copy of the emulator from you

  18. #18
    I would love to play with this emulator also.

    I have an old Fanuc OM-B that I am looking for trying to get another M code on.

    Mike in MN
    www.cncbasics.com

  19. #19
    Join Date
    May 2011
    Posts
    0

    PGMATE

    Quote Originally Posted by drdos View Post
    Check your PM
    HY, can you send me a copy for pg-emulator, i want to edit ladder in a 0-a.


    please send me a copy for pg emeulator

    bye

    Ezequiel Martinez
    CNC+

  20. #20
    Join Date
    Feb 2006
    Posts
    213
    Please do send it to me,

    [email protected]

    Quote Originally Posted by drdos View Post
    I have a PG Mate emulator. It runs on XP. But I think you have to use a special EProm Reader/Writer NOT the Fanuc PMC writer. I have never used it but I can send you a copy. It is 3.25 MEG Zip file. It was designed just for what you are trying to do and it's free. Do you want a copy?

Page 1 of 2 12

Similar Threads

  1. FANUC LADDER III V5.8 or later
    By ker2008 in forum Fanuc
    Replies: 12
    Last Post: 05-20-2019, 12:24 PM
  2. fanuc ladder
    By poss31 in forum Fanuc
    Replies: 6
    Last Post: 05-31-2016, 04:50 AM
  3. fanuc 0-mb ladder
    By Nazarioesc in forum Community Club House
    Replies: 1
    Last Post: 12-14-2013, 05:12 PM
  4. Scrap value quesiton, chips vs chunks. Coolant mixed with chips?
    By trialanderror in forum Uncategorised MetalWorking Machines
    Replies: 5
    Last Post: 10-04-2013, 12:08 AM
  5. ladder fanuc om-a
    By rathi_vk in forum DNC Problems and Solutions
    Replies: 1
    Last Post: 01-11-2009, 08:34 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •