[rajesh_1355]

ALARM: EMERGENCY EXIN
M01 OPERATION ERROR XZ

Detail of machine are as under,


NC - MELDAS MAGIC 64L
PC - MAGIC Pro-HI/L ( INTL) BDD - A02 W016 - A0
PLC - ECOCA - ELALL - M5
SYSTEM ID - 2090745880



In this machine, system power supply gone bad. We replaced the supply , now we are facing following alarms,
EMERGENCY EXIN

M01 OPERATION ERROR XZ

According to the electrical diagram, hard over travel switches are optional & are missing in machine.
In diagnosis mode, checked other inputs like cycle start , mode change switch which are ok.
Surprisingly no any out put is being generated.
Tried to check the PLC ladder but it is not being open. When searched any input like X29 or similar it shows ERROR.
When tried to check PLC size it shows
LINK 0 / KBYTE
LADDER 0 / KB
MESSAGE 0/ KB
I loaded all data by floppy even then it shows the same alarm. ( path c:/ncbac )

Next Day Work::stickpoke

To-day I reloaded all the data, but still no improvement & same alarm is being displayed.
In Meldas Magic screen tried to open the PLC ladder.
Sequence ... Ctr + F , Menu , 9main, monitor , NO / NC , X1F & enter it shows Prog not found.


When I tried to search by Rung No. 100,
PLC ladder is being displayed but when I checked whole ladder, no any X or Y contact was found.


I am quite confused, pl help.
In seven segment display of controller it shows " A "


( Can we load the data with the help of RS232 port.)

PL send your suggestion to solve the problem..

Thanks:drowning::drowning::drowning:

[Russell840]

Hi there
Dear advantures , I have a milling machine , whitch work with meldas magic64.
as I read in manuals , After installing softwars , transfer parameters on " HI-M " ,I need to set and adjust the NC parameters conforming to the machine configuration and machine specifications.
Unfortonatly I dont Know How?

[Russell840]

[QUOTE=Russell840;1956302]Hi there
Dear advantures , I have a milling machine , whitch work with meldas magic64.
as I read in manuals , After installing softwars , transfer parameters on " HI-M " ,I need to set and adjust the NC parameters conforming to the machine configuration and machine specifications.
Unfortonatly I dont Know How?



Finally I found the answer , and run the machine :cheers:
Well, if there is any quastion , its my plasure to help.
Best regurds
Russell

[Kashif]

Hi Russell840

I need your help

I have a hartford machining center, whitch work with meldas magic64.

I need system floppys

Meldas magic64 nc system disk 1 and 2
Meldas magic utility disk 1 and 2
Meldas magic meldasmagic monitor disk 1
Meldas magic custom API library runtime disk 1 and 2
Meldas magic64 NC data 64m disk 1

Please help me
If u have these floppy's please send me a soft copy

My email. [email protected]
Thanks in advance

[Kashif]

Hi Russell840

I need your help

I have a hartford machining center, whitch work with meldas magic64.

I need system floppys

Meldas magic64 nc system disk 1 and 2
Meldas magic utility disk 1 and 2
Meldas magic meldasmagic monitor disk 1
Meldas magic custom API library runtime disk 1 and 2
Meldas magic64 NC data 64m disk 1

Please help me
If u have these floppy's please send me a soft copy

My email. [email protected]
Thanks in advance

Mitsubishi Meldas Magic64 PC Based
System SoftWare Disk

AOMEI complete disk image

https://drive.google.com/drive/mobile/folders/1ENcGRNDRlsExITohcSXAEkZUd5pFOblP?usp=sharing

[Semoogad]

[QUOTE=Russell840;1963822]

Hi there
Dear advantures , I have a milling machine , whitch work with meldas magic64.
as I read in manuals , After installing softwars , transfer parameters on " HI-M " ,I need to set and adjust the NC parameters conforming to the machine configuration and machine specifications.
Unfortonatly I dont Know How?



Finally I found the answer , and run the machine :cheers:
Well, if there is any quastion , its my plasure to help.
Best regurds
Russell

[Semoogad]

[QUOTE=Russell840;1963822]

Hi there
Dear advantures , I have a milling machine , whitch work with meldas magic64.
as I read in manuals , After installing softwars , transfer parameters on " HI-M " ,I need to set and adjust the NC parameters conforming to the machine configuration and machine specifications.
Unfortonatly I dont Know How?



Finally I found the answer , and run the machine :cheers:
Well, if there is any quastion , its my plasure to help.
Best regurds
Russell

Hello
Can u help i have the same emg exin in my machine how to solve

[Jaanus50]

I have a Ecoca el4615, unfortunatly windows battery goes empty and after that Magicpro HI/L gives fault "Protection key not found" . Machine is working on Magicmon. Somewhere should be protection key file. Any ideas?

[malego]

I have a Ecoca el4615, unfortunatly windows battery goes empty and after that Magicpro HI/L gives fault "Protection key not found" . Machine is working on Magicmon. Somewhere should be protection key file. Any ideas?

Did you fix your problem? I have the exact same error message :"Protection key not found".
I installed everything from scratch on a new PC. Everything works fine as far as the Meldasmagic configuration and startup.
Only Magicpro HI/L is complaining at startup saying the :"Protection key not found".
I can't find any "key" or registry entry or file for that...
Any one can help?