[bill4807]

vtc 30 elite, funny thing is in the shop we have 6 of them.
Two of them with 20-m controller cycle works but the 21-m panels don't lol.
i'm sure its just a enable bit that needs to be turn from 0 to 1 but which one.

Did you check parameter 6700 and 6710?
Is this a part count for the Fanuc screen? As in the settings page...or do you have a LED display on the from OP panel?

[JrEngr1982]

forgot to check the 6700, but theses are the panels.
https://photos.app.goo.gl/JObKRDUCQYZyO2O83
https://photos.app.goo.gl/LUnUy66fBxSmnR5z2

[Jitu1234]

[QUOTE=Perfect Circle;1107771]Fanuc 18T Param.

PARAMETERS OF DISPLAYING OPERATION TIME AND NUMBER OF PARTS

Bit
PCM

M code that counts the total number of machined parts and the number of machined parts0 :M02, or M30, or an M code specified by parameter No.

6710 :Only M code specified by parameter No. 6710

6710 M code that counts the total number of machined parts and the number of machined parts

[Valid data range]

0 to 255 except 98 and 99The total number of machined parts and the number of machined parts arecounted (+1) when the M code set is executed.

Note:
Set value 0 is invalid (the number of parts is not countedfor M00). Data 98 and 99 cannot be set.

6711 Number of machined parts
Setting entry is acceptable.

[Data type]
2–word
[Unit of data]
One piece
[Valid data range]
0 to 99999999The number of machined parts is counted (+1) together with the totalnumber of machined parts when the M02, M30, or a M code specified byparameter No. 6710 is executed.

6712 Total number of machined parts
Setting entry is acceptable.
[Data type]
2–word
[Unit of data]
One piece
[Valid data range]
0 to 99999999This parameter sets the total number of machined parts.

The total number of machined parts is counted (+1) when M02, M30, oran M code specified by parameter No. 6710 is executed.

6713 Number of required parts

Setting entry is acceptable.
[Data type]
Word
[Unit of data]
One piece
[Valid data range]
0 to 9999This parameter sets the number of required machined parts.Required parts finish signal PRTSF is output to PMC when the number of machined parts reaches the number of required parts. The number of partsis regarded as infinity when the number of required parts is zero. ThePRTSF signal is then not output.

6750 Integrated value of power–on period

Setting entry is acceptable.
[Data type]
2–word
[Unit of data]
One minute
[Valid data range]
0 to 99999999This parameter displays the integrated value of power–on period.

6751 Operation time (integrated value of time during automatic operation)

Setting entry is acceptable.
[Data type]
2–word
[Unit of data]
One ms
[Valid data range]
0 to 60000

6752 Operation time (integrated value of time during automatic operation)
Setting entry is acceptable.
[Data type]
2–word
[Unit of data]
One minute
[Valid data range]
0 to 99999999This parameter displays the integrated value of time during automaticoperation (neither stop nor hold time included).

6753 Integrated value of cutting time

Setting entry is acceptable.
[Data type]
2–word
[Unit of data]
One ms
[Valid data range]
1 to 60000

6754 Integrated value of cutting time

Setting entry is acceptable.
[Data type]
2–word
[Unit of data]
One minute
[Valid data range]
0 to 99999999This parameter displays the integrated value of a cutting time that isperformed in cutting feed such as linear interpolation (G01) and circularinterpolation (G02 or G03).

6755 Integrated value of general–purpose integrating meter drive signal (TMRON)ON time

Setting entry is acceptable.
[Data type]
2–word
[Unit of data]
One ms
[Valid data range]
0 to 60000

6756 Integrated value of general–purpose integrating meter drive signal (TMRON)ON time

Setting entry is acceptable.
[Data type]
2–word
[Unit of data]
One minute
[Valid data range]
0 to 99999999This parameter displays the integrated value of a time while input signalTMRON from PMC is on.

6757 Operation time (integrated value of one automatic operation time)

Setting entry is acceptable.
[Data type]
2–word
[Unit of data]
One ms
[Valid data range]
0 to 60000

6758 Operation time (integrated value of one automatic operation time)

Setting entry is acceptable.
[Data type]
2–word
[Unit of data]
One minute
[Valid data range]
0 to 99999999
This parameter displays the one automatic operation drive time (neitherstop nor hold state included). The operation time is automatically presetto 0 during the power–on sequence and the cycle start from the reset state.

Part count ,run time not showing in screen

[MirNar]

https://youtu.be/AMqEtERgcPA

[ashanh]

I have a similar issue on my Fanuc 16TT control. The clock stopped running and is frozen. I can change it but it does not tick. Automatic operation is also not working and gives 1106 cycle time alarm. Thank You!

[drdos]

Back up EVERYTHING and clear memory.

[ashanh]

Back up EVERYTHING and clear memory.

Thank you drdos. I reset the machine with DELETE+RESET keys at power on. It cleared all the data but the date time values did not change at power up. I then took the motherboard out disconnected the apc battery cable and shorted the super cap. At power up the values did change however, the clock is still not ticking.