[cnctoolman]

Figured I would post it here aswell.

--------------------------------------------------------------------------------

I am looking at purchasing a nice used Journeyman 325 with the Dynapath 20 control on it. I have an appointment coming up to go inspect it in person. I did a simple program up in my CAD/CAM and would like someone who is familiar with the control to go over and see if my post is outputting the correct code. I am more familiar with Fanuc style code.

Thanks for any help in advance.

1/4" tool used for all operations.

First operation

Drill down .5" pecking with full retract .1 deep at a time

Mill an inside square pocket 2"x2"

Final- mill an outside 4" diameter circle with a .250 lead in /lead out radius

(1)$
N2(T)TOOL 1$
N4(T)OPERATION 1$
N6(9)T0001M6E54$
N8(9)M8$
N10(9)M3S3000$
N12(0)X0Y0$
N14(0)Z0$
N16(0)Z0.1$
N18(0)X0Y0Z-0.5K0.1W0.1F5.0G3$
N20(0)Y0.5$
N22(0)X0.5Y0$
N24(0)X0Y-0.5$
N26(0)X-0.5Y0$
N28(0)G0$
N30(T)TOOL 1$
N32(T)OPERATION 2$
N34(0)X0$
N36(1)Z-0.05$
N38(1)Y-0.125$
N40(1)X0.125F50.0$
N42(1)Y0.125$
N44(1)X-0.125$
N46(1)Y-0.125$
N48(1)X0$
N50(1)Y-0.25$
N52(1)X0.25$
N54(1)Y0.25$
N56(1)X-0.25$
N58(1)Y-0.25$
N60(1)X0$
N62(1)Y-0.375$
N64(1)X0.375$
N66(1)Y0.375$
N68(1)X-0.375$
N70(1)Y-0.375$
N72(1)X0$
N74(1)Y-0.5$
N76(1)X0.5$
N78(1)Y0.5$
N80(1)X-0.5$
N82(1)Y-0.5$
N84(1)X0$
N86(1)Y-0.625$
N88(1)X0.625$
N90(1)Y0.625$
N92(1)X-0.625$
N94(1)Y-0.625$
N96(1)X0$
N98(1)Y-0.75$
N100(1)X0.75$
N102(1)Y0.75$
N104(1)X-0.75$
N106(1)Y-0.75$
N108(1)X0$
N110(1)Y-0.875$
N112(1)X0.875$
N114(1)Y0.875$
N116(1)X-0.875$
N118(1)Y-0.875$
N120(1)X0$
N122(0)Z0.1$
N124(0)Y0$
N126(0)Z0.05$
N128(1)Z-0.1F5.0$
N130(1)Y-0.125$
N132(1)X0.125F50.0$
N134(1)Y0.125$
N136(1)X-0.125$
N138(1)Y-0.125$
N140(1)X0$
N142(1)Y-0.25$
N144(1)X0.25$
N146(1)Y0.25$
N148(1)X-0.25$
N150(1)Y-0.25$
N152(1)X0$
N154(1)Y-0.375$
N156(1)X0.375$
N158(1)Y0.375$
N160(1)X-0.375$
N162(1)Y-0.375$
N164(1)X0$
N166(1)Y-0.5$
N168(1)X0.5$
N170(1)Y0.5$
N172(1)X-0.5$
N174(1)Y-0.5$
N176(1)X0$
N178(1)Y-0.625$
N180(1)X0.625$
N182(1)Y0.625$
N184(1)X-0.625$
N186(1)Y-0.625$
N188(1)X0$
N190(1)Y-0.75$
N192(1)X0.75$
N194(1)Y0.75$
N196(1)X-0.75$
N198(1)Y-0.75$
N200(1)X0$
N202(1)Y-0.875$
N204(1)X0.875$
N206(1)Y0.875$
N208(1)X-0.875$
N210(1)Y-0.875$
N212(1)X0$
N214(0)Z0.1$
N216(0)Y0$
N218(0)Z0$
N220(1)Z-0.15F5.0$
N222(1)Y-0.125$
N224(1)X0.125F50.0$
N226(1)Y0.125$
N228(1)X-0.125$
N230(1)Y-0.125$
N232(1)X0$
N234(1)Y-0.25$
N236(1)X0.25$
N238(1)Y0.25$
N240(1)X-0.25$
N242(1)Y-0.25$
N244(1)X0$
N246(1)Y-0.375$
N248(1)X0.375$
N250(1)Y0.375$
N252(1)X-0.375$
N254(1)Y-0.375$
N256(1)X0$
N258(1)Y-0.5$
N260(1)X0.5$
N262(1)Y0.5$
N264(1)X-0.5$
N266(1)Y-0.5$
N268(1)X0$
N270(1)Y-0.625$
N272(1)X0.625$
N274(1)Y0.625$
N276(1)X-0.625$
N278(1)Y-0.625$
N280(1)X0$
N282(1)Y-0.75$
N284(1)X0.75$
N286(1)Y0.75$
N288(1)X-0.75$
N290(1)Y-0.75$
N292(1)X0$
N294(1)Y-0.875$
N296(1)X0.875$
N298(1)Y0.875$
N300(1)X-0.875$
N302(1)Y-0.875$
N304(1)X0$
N306(0)Z0.1$
N308(0)Y0$
N310(0)Z-0.05$
N312(1)Z-0.2F5.0$
N314(1)Y-0.125$
N316(1)X0.125F50.0$
N318(1)Y0.125$
N320(1)X-0.125$
N322(1)Y-0.125$
N324(1)X0$
N326(1)Y-0.25$
N328(1)X0.25$
N330(1)Y0.25$
N332(1)X-0.25$
N334(1)Y-0.25$
N336(1)X0$
N338(1)Y-0.375$
N340(1)X0.375$
N342(1)Y0.375$
N344(1)X-0.375$
N346(1)Y-0.375$
N348(1)X0$
N350(1)Y-0.5$
N352(1)X0.5$
N354(1)Y0.5$
N356(1)X-0.5$
N358(1)Y-0.5$
N360(1)X0$
N362(1)Y-0.625$
N364(1)X0.625$
N366(1)Y0.625$
N368(1)X-0.625$
N370(1)Y-0.625$
N372(1)X0$
N374(1)Y-0.75$
N376(1)X0.75$
N378(1)Y0.75$
N380(1)X-0.75$
N382(1)Y-0.75$
N384(1)X0$
N386(1)Y-0.875$
N388(1)X0.875$
N390(1)Y0.875$
N392(1)X-0.875$
N394(1)Y-0.875$
N396(1)X0$
N398(0)Z0.1$
N400(0)Y0$
N402(0)Z-0.1$
N404(1)Z-0.25F5.0$
N406(1)Y-0.125$
N408(1)X0.125F50.0$
N410(1)Y0.125$
N412(1)X-0.125$
N414(1)Y-0.125$
N416(1)X0$
N418(1)Y-0.25$
N420(1)X0.25$
N422(1)Y0.25$
N424(1)X-0.25$
N426(1)Y-0.25$
N428(1)X0$
N430(1)Y-0.375$
N432(1)X0.375$
N434(1)Y0.375$
N436(1)X-0.375$
N438(1)Y-0.375$
N440(1)X0$
N442(1)Y-0.5$
N444(1)X0.5$
N446(1)Y0.5$
N448(1)X-0.5$
N450(1)Y-0.5$
N452(1)X0$
N454(1)Y-0.625$
N456(1)X0.625$
N458(1)Y0.625$
N460(1)X-0.625$
N462(1)Y-0.625$
N464(1)X0$
N466(1)Y-0.75$
N468(1)X0.75$
N470(1)Y0.75$
N472(1)X-0.75$
N474(1)Y-0.75$
N476(1)X0$
N478(1)Y-0.875$
N480(1)X0.875$
N482(1)Y0.875$
N484(1)X-0.875$
N486(1)Y-0.875$
N488(1)X0$
N490(0)Z0.1$
N492(T)TOOL 1$
N494(T)OPERATION 3$
N496(0)X-0.2622Y2.3737$
N498(1)Z-0.125F5.0$
N500(2)X-0.0109Y2.125I-0.0122J2.375D1$
N502(2)I0J0F50.0D0$
N504(2)X0.2378Y2.3763I-0.0122J2.375D1$
N506(0)Z0.1$
N508(9)M30$
END$

[jagardner4]

I didn't check every detail, but the code certainly looks like DynaPath conversational. It should load and run. Whether it gives you the exact part you're looking for, I can't be sure.

[T0DD]

(0001)
N1(T).250-DRILL$
N2T1M06
N3S900M03
N5(T)DRILL-5-HOLES$
N6G00X0.0Y0.0
N7Z1.
N8Z.1
N9G83X0.0Y0.0Z-.5R.1F3.K.1
N10X0.0Y.5
N11X.5Y0.0
N12X0.0Y-.5
N13X-.5Y0.0
N14G80
N15G00Z1.1
N16(T).250-ENDMILL$
N17T2M06
N18S600M03
N20(T)MILL-POCKET$
N21G00X0.0Y0.0
N22Z1.1
N23Z.1
N24G01Z-.15F20.
N25X.125F4.
N26Y.125
N27X-.125
N28Y-.125
N29X.125
N30Y0.0
N31X.25
N32Y.25
N33X-.25
N34Y-.25
N35X.25
N36Y0.0
N37X.375
N38Y.375
N39X-.375
N40Y-.375
N41X.375
N42Y0.0
N43X.5
N44Y.5
N45X-.5
N46Y-.5
N47X.5
N48Y0.0
N49X.625
N50Y.625
N51X-.625
N52Y-.625
N53X.625
N54Y0.0
N55X.75
N56Y.75
N57X-.75
N58Y-.75
N59X.75
N60Y0.0
N61X.875
N62Y.875
N63X-.875
N64Y-.875
N65X.875
N66Y0.0
N67X0.0
N68Z-.25
N69X.125
N70Y.125
N71X-.125
N72Y-.125
N73X.125
N74Y0.0
N75X.25
N76Y.25
N77X-.25
N78Y-.25
N79X.25
N80Y0.0
N81X.375
N82Y.375
N83X-.375
N84Y-.375
N85X.375
N86Y0.0
N87X.5
N88Y.5
N89X-.5
N90Y-.5
N91X.5
N92Y0.0
N93X.625
N94Y.625
N95X-.625
N96Y-.625
N97X.625
N98Y0.0
N99X.75
N100Y.75
N101X-.75
N102Y-.75
N103X.75
N104Y0.0
N105X.875
N106Y.875
N107X-.875
N108Y-.875
N109X.875
N110Y0.0
N111X0.0
N112G00Z1.1
N114(T)MILL-CIRCLE$
N115G00X0.0Y2.25
N116Z.1
N117G01Z-.125F20.
N118G41X-.125F4.
N119G17
N120G03X0.0Y2.125I0.0J2.25
N121G02X0.0Y2.125I0.0J0.0
N122G03X.125Y2.25I0.0J2.25
N123G40G01X0.0
N124G00Z1.1
N125M30
E

I broke it into 2 tools. Note: This is EIA format.

Todd

[T0DD]

Regardless of format (conversational or G-code) I think the you will fault out when it reads the "D" offset. On Fanuc you can pull any register value, not on dynapath. So delete that from your post!
Todd

[jagardner4]

The 'D' code in blocks 500, 502 and 504 are direction codes (0=CW, 1=CCW) in the conversational format and are needed. Also, I just noticed that your 'E' code (fixture offset) in block 6 is too large. The control won't have 54 offsets (I suspect the post was trying for a G54). Try a smaller number like E01.

[cnctoolman]

Thanks for the tips. Will try and do an edit with Posthaste and see if I can get some better code out of it.

Is there any specific reasoning for all the $'s

[jagardner4]

The '$' is the conversational end-of-block character.

G-code blocks would use the line feed character as end-of-block, usually denoted as <LF>. It is an ASCII code 10.

[garychipmaker]

You could run that in conversational event type 4 circle mill with about 30 seconds of programming

[cnctoolman]

gary,

Just checking the output from my CAM system, for when I get into more detailed work that I actually do. That was just something quick i came up with.

Also pulled the plug on the machine. Went and inspected it, and it was in very good condition. Looks to have been hardly used. So I bought it.