[Bad_German]

I am retrofitting my EMCO Turn 120P and have no use for these boards. I know some people will need them.
Unfortunately I cannot guarantee that they are working as I do not have 3phase power and did not test the controller prior to dis-assembly.
I bought the machine from my university where it has been in storage for many years (they have bigger CNC machines in use), the machine looks like it has barely been used. (minimal scratches and shavings in the machine, also the tool changer only has one clamp marking)

What I did notice is that the motherboard has some of the traces re-soldered, and the motor control board was lose. Only fitted with one screw, so the PCB is slightly warped. Everything else look as new still (the machine is from 1987).

If you need any of the boards please post here or pm me, I will find out the shipping cost.
This is what I have for sale:

2x Shrittmotor R3D413000 80 USD each


Axiscontroller R3D14001 20 USD


Controlle Netzteil R3D436001 20 USD


Datacontroller R3D415000 20 USD


Machineninterface R3D425001 20 USD


Motherboard/s 5 USD


Motor Driver Board A7B418000 (tool turret board) 10 USD


Phasenschnittstellung R3D417000 20 USD


Regelkarte A7B416000 20 USD


Spindle Control R3D420010 10 USD


Videocarte R3D419000 20 USD


CRT Screen 20 USD

Or take the lot for 300 USD

[Barry Thomas]

Hi Stephan,

Sold, I will take the lot.

Please work out a shipping cost to send to Perth Australia, postal code 6111
and we can work out a payment method.
Please contact me on [email protected]

Thanks Barry Thomas

[Bad_German]

All the boards going to Barry Thomas,
Only the CRT is left, it weighs 4kg.
It's going to the bump at the end of the month if no one takes it.

[Zahnrad Kopf]

Any chance you have the manuals?

[Bad_German]

No unfortunately I did not get any manuals or tapes.
That's why I am retrofitting my machine to Linux CNC.

[Slavikas]

Hello, there are still at least 1 card?

[honda750]

Hello!
Has a EMCO VMC-100 and need:
I want to buy Controlle Netzteil R3D436001 you. What will this cost me a total with shipping?
Also need stepper motor cards 3 x No. R3D413000?

For shipping Item must be packed with anti-static material.

Gerhard Hansen
addr.:
Sollivegen 44,
6414 Molde
Norway

[mrdeveloper]

Hei!

I have a T1 lying around that i recently bought for spare parts. I might be able to help you with the R3D436001 card, but the driver boards I am affraid are allready scavenged for my two M1 controllers (for EMCO F1P).

The T1 unit has been in use til recently at a school and has been well taken care of. It runs of 3 phase AC 230V. It has also been upgraded with some custom logic boards that were used for extra automation. I offer the whole T1 for sale (sans the two driver boards). Shipping was expensive, I paid about the same for shipping as I did for the unit itself (weighs in on around 80kg). Price would be 2000kr + shipping. You could also just buy the card. Ill let it go for 500kr + shipping.

Also a tip for you, since you are in Norway: put a search agent on "finn.no" with search terms "EMCO CNC" and wait a few months. I have found no less than 5 F1P machines this way in a year's time (two of them I bought). You may be able to find a broken machine that can be scavenged.

Oh, and as mentioned before, the M1 and T1 are very similar (chassis, controls and most parts inside), so if you find an M1 it should work for you.

Good luck!

[Menio13]

Witam czy są jakieś części dostępne do emcotronic 120 emcotronic t1
Shrittmotor R3D413000