584,842 active members*
4,491 visitors online*
Register for free
Login
Results 1 to 10 of 10
  1. #1
    Join Date
    Jan 2013
    Posts
    9

    Mazatrol T-Plus

    I'm using a 2011 Mazak Slant Turn 60 (with Mazatrol T-Plus controls). When in manual mode (e.g. Rapid) the turret can only move 1 axis at a time either X or Z axis. The Slant Turn 450 (with Mazatrol T-Plus controls) I used before could move both X and Z axis together in manual mode. Is there a parameter I can change to allow the ST60 to do the same? I looked through the parameter list, couldn't find it. Any ideas?

  2. #2
    Join Date
    May 2004
    Posts
    4519
    Since this is a relatively new machine, what did the nearest Mazak rep tell you when you called them with this question during their regular business hours?

  3. #3
    Join Date
    Jan 2013
    Posts
    9
    Whenever there is an engineer in servicing a machine or giving training I have asked them, they say they will find out for me but they never do. I just had a look on the Mazak homepage and found a 24hr hotline number: 01905 752000. I'll try that when I'm at the controls. There doesn't seem to be any online support.

  4. #4
    Join Date
    Dec 2007
    Posts
    300
    The last T+ controls were built in 1996.

  5. #5
    Join Date
    Jun 2012
    Posts
    36

    CHECK THIS PARAMETER

    HEI FRIEND,

    PL CHECK THIS R54 BIT 0 PLC PARAMETER.

    IF IT IS 0 MAKE IT 1.

    THE PAGE WILL BE 9 PAGE OR SO AND YOU CAN GO TO MACHINE PARAMETER SCREEN AND SCROLL FOR THIS PAGE.

    IT WILL BE LIKE R54 WITH 8 BITS SOME 1 AND SOME WITH 0.

    PL NNOTE DOWN THE ORIGINAL BEFORE CHANGING THE BIT.

    PL POST REPLY AFTER CHANGING THE BIT 0 TO 1.

    SHEKAR

  6. #6
    Join Date
    Jan 2013
    Posts
    9
    Quote Originally Posted by MrMazak View Post
    The last T+ controls were built in 1996.
    My bad it's a Mazatrol 640T controller.

  7. #7
    Join Date
    Jan 2013
    Posts
    9
    Quote Originally Posted by SHEKAR View Post
    HEI FRIEND,

    PL CHECK THIS R54 BIT 0 PLC PARAMETER.

    IF IT IS 0 MAKE IT 1.

    THE PAGE WILL BE 9 PAGE OR SO AND YOU CAN GO TO MACHINE PARAMETER SCREEN AND SCROLL FOR THIS PAGE.

    IT WILL BE LIKE R54 WITH 8 BITS SOME 1 AND SOME WITH 0.

    PL NNOTE DOWN THE ORIGINAL BEFORE CHANGING THE BIT.

    PL POST REPLY AFTER CHANGING THE BIT 0 TO 1.

    SHEKAR
    I changed the Machine Parameter R54 from "00100000" to "00100001", then switched the machine off and on at the controls and the main power switch. It worked. Thanks for the help.

    So on the Mazatrol 640T controls the Machine Parameter is R54.
    For X or Z axis (one at a time) it's - 00100000
    For X and Z axis (both together) it's - 00100001

  8. #8
    Dear Mr. Shekar
    We are having Mazak Qt 30 Machine with Mazatrol T Plus Control. Now we are getting Alarm 214 PLC - Parameter Input Error. Kindly Suggest to solve the Problem

  9. #9

    Re: CHECK THIS PARAMETER

    Quote Originally Posted by SHEKAR View Post
    HEI FRIEND,

    PL CHECK THIS R54 BIT 0 PLC PARAMETER.

    IF IT IS 0 MAKE IT 1.

    THE PAGE WILL BE 9 PAGE OR SO AND YOU CAN GO TO MACHINE PARAMETER SCREEN AND SCROLL FOR THIS PAGE.

    IT WILL BE LIKE R54 WITH 8 BITS SOME 1 AND SOME WITH 0.

    PL NNOTE DOWN THE ORIGINAL BEFORE CHANGING THE BIT.

    PL POST REPLY AFTER CHANGING THE BIT 0 TO 1.

    SHEKAR
    hi,
    do you have any manuals for QT25C with mazatrol t plus?
    sting

  10. #10
    Join Date
    Jan 2013
    Posts
    9
    Quote Originally Posted by sting007 View Post
    hi,
    do you have any manuals for QT25C with mazatrol t plus?
    sting
    cncmanual.com/mazak/
    Try there, they have lots of manuals for lots of machines.

Similar Threads

  1. Mazak M-4 Mazatrol T2 and mazatrol Cam T2 operating manual in english
    By tuanpq in forum Mazak, Mitsubishi, Mazatrol
    Replies: 31
    Last Post: 07-09-2021, 04:06 PM
  2. MAZATROL T-PLUS
    By CHANDRU in forum Mazak, Mitsubishi, Mazatrol
    Replies: 4
    Last Post: 12-14-2013, 11:09 PM
  3. Mazatrol t plus
    By Nichidrill in forum Mazak, Mitsubishi, Mazatrol
    Replies: 0
    Last Post: 01-19-2013, 10:34 PM
  4. Sm1 well versed with mazatrol 640m or atleast ne mazatrol
    By naren1608 in forum Mazak, Mitsubishi, Mazatrol
    Replies: 0
    Last Post: 03-22-2010, 11:29 AM
  5. mazatrol cam M2
    By spickett in forum Mazak, Mitsubishi, Mazatrol
    Replies: 3
    Last Post: 03-25-2008, 01:34 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •