[jeepers94]

I have a Chinese made 6090 cnc router.I am not sure who manufactured it. It is sold
in the US by Baileigh as the WR-23. It has the RichAuto handheld usb controller RZNC-0501.
I am trying to use DeskProto under plain g-code inch. I have also tried plain g-code mm.
I choose U disk,then the iso file.It shows the parameters.I press ok,but the program doesn't run.
It goes back to the initial xyz screen.
I know this controller is used by many.If someone could let me know what works for them
with this controller, it would sure help.

[jalessi]

I have a Chinese made 6090 cnc router.I am not sure who manufactured it. It is sold
in the US by Baileigh as the WR-23. It has the RichAuto handheld usb controller RZNC-0501.
I am trying to use DeskProto under plain g-code inch. I have also tried plain g-code mm.
I choose U disk,then the iso file.It shows the parameters.I press ok,but the program doesn't run.
It goes back to the initial xyz screen.
I know this controller is used by many.If someone could let me know what works for them
with this controller, it would sure help.

Jeepers94,

Have you reviewed the attached manual?

The documentation may be better than what you received with your machine.

Welcome to the Zone,

Jeff...

[bettylee410]

I have a Chinese made 6090 cnc router.I am not sure who manufactured it. It is sold
in the US by Baileigh as the WR-23. It has the RichAuto handheld usb controller RZNC-0501.
I am trying to use DeskProto under plain g-code inch. I have also tried plain g-code mm.
I choose U disk,then the iso file.It shows the parameters.I press ok,but the program doesn't run.
It goes back to the initial xyz screen.
I know this controller is used by many.If someone could let me know what works for them
with this controller, it would sure help.

Jeepers94, the RNZC 0501 can also accept *mmg format file directly, you can try *mmg file again. And you can get *mmg from Artcam software.

[jeepers94]

The manuals provided by Baileigh are very good. The hand held control is setup for my machine. I went through
it and compared settings to mine. They were spot on. The router does see and use the demo .cnc and .mmg
files on the control. If I try a usb flash drive, it sees the file but will not attempt to run it. I tried several .stl
files run through DeskProto. I made sure the usb was fat 32 and 1 gig. I am wondering if the usb port is
working correctly. It says in the manual anything but fat 32 will crash it. Maybe someone along the chain tried
a different format. I downloaded some other trial software to try. Most of my work will be using stl files so I need
a compatible software. I am also going to try going directly to the control from my laptop.

[jalessi]

Jeepers94,

Have you tried to run a .tap file?

Jeff...

[jeepers94]

I tried a tap file from V Carve Photo. It did not even show the file name. I also tried to work
directly from my laptop. It didn't work either. I am 70% sure my hand held control is bad.
The company I bought it from agrees, and are sending me a new one. I am new to cnc but
have used high end vinyl cutters for several years. I will let you know in about a week, how
it works.

[jeepers94]

They sent a new control,but it was setup for the larger machine.It still will not read my files.
Does anyone have a simple file they used on this control? Or if you have that control could
I send you a .stl file to write a file for me to try on my machine?

[jalessi]

Jeepers94,

Check your messages.

Jeff...

[jeepers94]

Well Jeff,that did not work either.I tried 6 files on my flash drive. I had inch and mm of .tap.cnc and
plain g code from DeskProto. The file names do not even show on the lcd screen.
I had 1 other thought. The RichAuto site says the drive comes with a U drive with Windows
system files on it. Mine did not have the drive. Is it possible there are usb drivers on the drive
that I need? My router runs the onboard demos,so the router is not the problem. It has to be
the hand control,the cable to the control,the circuit board or the missing flash drive files.
The new control I was sent wassetup to the larger router.It is the same control and the
files did not show on that unit either.Of course no flash drive with it either.
After 2 months of trying to get up and running,I am about to drive to the company
headquarters and have it out with them!

[jalessi]

Jeepers94,

Purchase a new Sandisk 2 Gigabyte flash drive, format it with FAT32 then copy a .tap file to it.

The controller needs to be in the U Disk screen.

Jeff...

[angelmoi]

greetings

Friends, one way it works is: upload any kind of machine .nc, .cnc .tap file into the pendant using the copy option, them run it, amazingly it works

[Melkiades]

Jeepers94: It may happens by wrong flash drive controller, or wrong USB drive format.
I have positive experience with USB brand Trancend and A-data, negative with Apacer
Use as small drive as possible (128Mb-1Gb are perfect). Look over your or your neightborn's houses for old used drives.
Also, this unit support only FAT/FAT32/NTFS system with block size not over 4096kb
Try "format F: /FS:FAT32 /A:1024" from commant line, it should help. Replace F: with name or your connected drive letter
File extension doesn't matter.
Good luck!

[nirosh]

why dsp 0501 not accept m3 and m5 comand..i need to controling spindle from G Code..but i cant that..

[Melkiades]

Works fine for me.
May be your problem with wire connection?
At J7 connector signals from S0 and SP- should be connected to invertor properly.

[nirosh]

Works fine for me.
May be your problem with wire connection?
At J7 connector signals from S0 and SP- should be connected to invertor properly.

I connected properly ..but spindle start at the beginning .
and after finish g code it stopping..if i give in between M3 and M5 with g code it will not work.that mean its working from hime selfe..not from the g code.i need several time to off and on spindle from my g code..