508,135 active members
3,342 visitors online
Register for free
Login
IndustryArena Forum > Hobby Projects > Gunsmithing > Lathe & Milling machines needed
Results 1 to 6 of 6
  1. #1

    Lathe & Milling machines needed

    Hello, all. This is my first post. This looked like exactly the forum I have been looking for.

    I am an 07 FFL, a firearms manufacturer. Most of our firearms can be made in our shop. Certain steps have been farmed out to others such as milling slots in a receiver tube and turning down an assault rifle barrel shoulder so the barrel will time. Most parts have been made by others as we buy quantities of parts to build the guns.

    Now I would like to keep all processes in-house. So I need a basic metal lathe (mostly to turn barrel shoulders) which is simple. I need a milling machine to mill slots 1/2" wide and 6" long. The mill must also drill very accurate holes from .125" to 1/2" in diameter. The mill also has to make cutouts in tubing that are square. Sight dovetails also need to be milled.

    Most of what we build are FN-FAL's, L1A1's, Model 1911 .45ACP pistols and the AR in it's variants. Also M1 Garands and M-1 Carbines.

    So I believe that I need rather basic machines and used would fit my budget.

    I welcome any advice and hope to find the used lathe and mill I need.

    Thanks,

    Steve

  2. #2
    Registered
    Join Date
    Mar 2006
    Posts
    2712
    You need to supply a bit more info. Budget $$$, center to center distance on lathe, table size and travel for the mill etc.

    Price doesn't guarantee quality but quality is seldom cheap.

    Dick Z
    DZASTR

  3. #3
    Hellow Richard:

    My budget is $1,500.00 US.

    The FAL barrel that has to go through the chuck measures 3/4" diameter at the largest and 21" long.

    Since the barrel can be inserted through the chuck the distance from chuck to tailstock doesn't have to be very long. I only want to shave off a little metal from the barrel shoulder to time the barrel to the upper receiver.

    The milling machine will be used for cutting sight dovetails. Also for milling slots in tube receivers and boring accurate holes in tube receivers.

    I have seen ads for mini-mills, but the information is to scant to know if they would work.

    I hope this info helps and look forward to any suggestions.

    Thanks, Steve

  4. #4
    Registered
    Join Date
    Oct 2005
    Posts
    35
    Steve,
    The $1500 budget wont get you what you want and need for accurate gunsmithing work. You might find a used lathe that would suit your needs for somewhere close to that budget, but you will still need to add tooling. Adding a mill too will require more funds. Finding good used equipment with the ability to hold tolerances needed for gunsmithing will be challenging, if you are a good machinist you might get satisfactory results from older lightly used - but that is hard to find. A mini-mill is not going to do 1/2" slots in steel with any kind of accuracy or speed. Increasing your budget by a factor of 4 or 5 might get you the kind of equipment you need, but then again add tooling and measurement equipment and you will quickly be way beyond that.

    Then you need the skills to operate the equipment in a manner that produces the quality desired and holds the tolerances necessary. Not to mention that the learning curve can be expensive if you mess up an expensive gun component. Unless you are prepared to spend the dollars and invest the time to learn the equipment, you might be better off retaining the outside machining services.

  5. #5
    Thank you for your advice and help. It does look like my budget was way off. My problem also involves finding a machine shop to farm the work out to. They don't exist in my part of rural Florida. The machinist is a lost art. A shop that turns brake drums calls itself a machine shop. I have gone to, or called, every one in the three cities around me. There is not one machine shop with lathe and mill. I had hoped a mini mill would make the 1/2" slots in perhaps 1/4" cuts. I will keep looking for a solution.

    Steve

  6. #6
    Registered
    Join Date
    Apr 2005
    Posts
    444

    Re: Lathe & Milling machines needed

    Read up on the ITAR regulations before you get too excited the BR6.5 website has some posts on it If you are {Building} or assembling guns and doing any machine work for pay it is a $2500.00 per year cost on top of the FFL License.

Similar Threads

  1. Draw comparison between CNC and conventional lathe amd milling machines
    By fayysl in forum Uncategorised MetalWorking Machines
    Replies: 3
    Last Post: 12-19-2010, 09:47 PM
  2. CNC milling&lathe machines and accessories
    By jinandexiaoyan in forum Uncategorised MetalWorking Machines
    Replies: 0
    Last Post: 12-12-2009, 06:41 AM
  3. CNC milling&lathe machines and accessories
    By jinandexiaoyan in forum Uncategorised MetalWorking Machines
    Replies: 0
    Last Post: 12-12-2009, 04:44 AM
  4. CNC milling&lathe machines and accessories
    By jinandexiaoyan in forum General Metalwork Discussion
    Replies: 0
    Last Post: 12-02-2009, 08:33 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •