500,469 active members
4,839 visitors online
Register for free
Login
Results 1 to 9 of 9
  1. #1
    Registered
    Join Date
    Dec 2013
    Posts
    3

    Angry Mori Seiki SL1 Yasnac LX2

    Problem started with the display would not advance. Program running position display or any of the display buttons would not function until program stop command.
    LX2 was sent to Yaskawa for repair. It came back with the same problem. Sent it back, it returned with no crt display. Sent it back, it returned with the position display at every .328 of motion the display will jump .328 positive, continue to move axis same direction and it will jump .328 negative. Yaskawa cannot see the problem at there test and repair department. But they did program the control new eproms. The axes do not physically jump, and it is X and Z which act the same. The problem is present with pulse handle, manual jog buttons and in MDI. Does anyone have an SL1 that I could send boards to, in order to isolate the problem? Any address would be appreciated.

    Thanks Rick

  2. #2
    Gold Member
    Join Date
    Feb 2009
    Posts
    5958

    Re: Mori Seiki SL1 Yasnac LX2

    Let me get this correct. If you move an axis, it simply goes the wrong way, or is the axis physically jumping?

  3. #3
    Registered
    Join Date
    Dec 2013
    Posts
    3

    Re: Mori Seiki SL1 Yasnac LX2

    Axes move in correct direction and they do not jump. Only the display jumps at .328 it will add and then subtract travelling in the same direction.

  4. #4
    Registered
    Join Date
    Jan 2015
    Posts
    42

    Re: Mori Seiki SL1 Yasnac LX2

    Are you still struggling with this? Let me know I have an idea for you.
    Thanks
    Bob

  5. #5
    Registered
    Join Date
    Dec 2013
    Posts
    3

    Re: Mori Seiki SL1 Yasnac LX2

    Thanks for the reply Bob

    Yes, machine is down, Yaskawa has been no help. Looking for a cp4 board to test with. Please any idea would help.

    Rick




    Quote Originally Posted by ncbobbys View Post
    Are you still struggling with this? Let me know I have an idea for you.
    Than
    Bob

  6. #6
    Registered
    Join Date
    Jan 2015
    Posts
    42

    Re: Mori Seiki SL1 Yasnac LX2

    Rick... check the board and see if is a CP04 or CP04B
    email me : simplersys@gmail.com

  7. #7
    Registered
    Join Date
    Feb 2014
    Posts
    1

    Re: Mori Seiki SL1 Yasnac LX2

    Hello

    I have a SL-1A with yasnac control,
    Do you still troubleshooting the control? there must be somthing to compare between lathes.
    I am also dealing with a issue in automatic mode
    let me know what happen with your lathe

    Regards

  8. #8
    Registered
    Join Date
    Jul 2007
    Posts
    62

    Re: Mori Seiki SL1 Yasnac LX2

    Good Morning, by any chance do you have the electrical diagram for your Mori Seiki SL-1? I am willing to pay for a copy of it.

  9. #9
    Registered
    Join Date
    Jul 2007
    Posts
    62

    Re: Mori Seiki SL1 Yasnac LX2

    Quote Originally Posted by Franco1 View Post
    Hello

    I have a SL-1A with yasnac control,
    Do you still troubleshooting the control? there must be somthing to compare between lathes.
    I am also dealing with a issue in automatic mode
    let me know what happen with your lathe

    Regards
    Good Morning, by any chance do you have the electrical diagram for your Mori Seiki SL-1? I am willing to pay for a copy of it.
    Email masamayoa@hotmail.com

Similar Threads

  1. Mori Seiki SL2 With YASNAC
    By Antonio Arguijo in forum Mori Seiki Mills
    Replies: 5
    Last Post: 05-19-2019, 11:12 PM
  2. Mori Seiki CL-20A YASNAC
    By lalorockero in forum Mori Seiki lathes
    Replies: 4
    Last Post: 07-20-2013, 06:01 AM
  3. Mori Seiki CL-20 Yasnac LX3 Alarm 330 & 310
    By Nevronplastics in forum Mori Seiki lathes
    Replies: 5
    Last Post: 01-16-2013, 11:37 PM
  4. Mori Seiki MV45 Yasnac MX1 Help Please
    By premier_industr in forum G-Code Programing
    Replies: 6
    Last Post: 10-21-2011, 10:59 AM
  5. Mori Seiki MV45 Yasnac MX1 Help Please
    By premier_industr in forum Mazak, Mitsubishi, Mazatrol
    Replies: 6
    Last Post: 01-27-2007, 06:04 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •