584,842 active members*
4,491 visitors online*
Register for free
Login
IndustryArena Forum > CNC Electronics > Stepper Motors / Drives > how to connect( hydiv268n-5a to mach 3 5 axis board
Results 1 to 4 of 4
  1. #1
    Join Date
    Dec 2015
    Posts
    7

    Angry how to connect( hydiv268n-5a to mach 3 5 axis board

    hey every one
    it is a really problem
    because i hade one driver is gone .........
    so i need the correct connection and all the photos from internet not have that compaination
    the driver is ((( http://www.cnczone.com/forums/attach...d=300252&stc=1 )))
    the interface board is ((( mach 3 5 axis board )))http://www.cnczone.com/forums/attach...d=300250&stc=1
    i hope some one help me

  2. #2
    Join Date
    May 2005
    Posts
    1397

    Re: how to connect( hydiv268n-5a to mach 3 5 axis board

    Why not contact the people you purchased the units from? Don't they offer technical support? I always support the units I sell...
    James hosts the single best wiki page about steppers for CNC hobbyists on the net:
    http://www.piclist.com/techref/io/steppers.htm Disagree? Tell him what's missing! ,o)

  3. #3
    Join Date
    Mar 2018
    Posts
    1

    Re: how to connect( hydiv268n-5a to mach 3 5 axis board

    Hello
    I have the same 5-axis board and the same driver.
    Could you tell me how you connected?
    Thank you very much.

  4. #4
    Join Date
    Mar 2007
    Posts
    2083

    Re: how to connect( hydiv268n-5a to mach 3 5 axis board

    for each stepper driver you can either
    connect all of the step + and direction + terminals to the +5V supply to the breakout board
    and the step - and direction - to the appropriate BOB outputs for the axis
    setting the outputs to active low in mach3

    or
    connect all of the step - and direction - terminals to the 0V / ground supply to the breakout board
    and the step + and direction + to the appropriate BOB outputs for the axis
    setting the outputs to active high in mach3

    John

Similar Threads

  1. Trying to get Mach 3 to connect to outputs
    By wld99 in forum Mach Software (ArtSoft software)
    Replies: 7
    Last Post: 03-22-2022, 12:19 PM
  2. How can i connect a HY VFD with MK 2/4 PROBOTIX board?
    By shanu4454 in forum Phase Converters
    Replies: 0
    Last Post: 09-21-2014, 04:19 AM
  3. 4 Axis CNC Stepper Motor TA8435H Driver Board Mach 2 3 question
    By s_sus in forum Stepper Motors / Drives
    Replies: 242
    Last Post: 04-29-2012, 06:36 PM
  4. 5-Axis CNC Stepper Motor TA8435H Driver Board Mach 2 3 question
    By aashijanani in forum Stepper Motors / Drives
    Replies: 2
    Last Post: 03-19-2010, 06:39 PM
  5. How to connect ELM Board and OSMC Board ?
    By bigeye3107 in forum Open Source Controller Boards
    Replies: 2
    Last Post: 06-16-2008, 12:26 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •