585,942 active members*
3,345 visitors online*
Register for free
Login
IndustryArena Forum > MetalWorking Machines > Novakon > Looking for a spindle driver board NM-145

Thread: Looking for a spindle driver board NM-145

Results 1 to 10 of 10
  1. 02-20-2016, 06:05 PM #1
    AiR_GuNNeR
    AiR_GuNNeR is offline Registered
    Join Date
    Feb 2010
    Posts
    371

    Looking for a spindle driver board NM-145

    I fried the spindle driver board on my NM-145 and would like to get up and running again ASAP. Anyone out there that retrofitted their mill willing to part with one? This is the small daughter board that mounts to the spindle power board.
    Eric
    Reply With Quote Reply With Quote
  2. 02-20-2016, 07:13 PM #2
    Novakon
    Novakon is offline Company Representative
    Join Date
    Aug 2008
    Posts
    400

    Re: Looking for a spindle driver board NM-145

    Hi Eric,

    There are a couple of options... call me back or send an email and we get started on the solution.

    Regards,
    John
    Reply With Quote Reply With Quote
  3. 02-20-2016, 07:28 PM #3
    AiR_GuNNeR
    AiR_GuNNeR is offline Registered
    Join Date
    Feb 2010
    Posts
    371

    Re: Looking for a spindle driver board NM-145

    Thanks John,
    I called and left a couple of messages with my phone number.
    Reply With Quote Reply With Quote
  4. 02-22-2016, 02:26 PM #4
    ies fixs
    ies fixs is offline Registered
    Join Date
    Apr 2012
    Posts
    84

    Re: Looking for a spindle driver board NM-145

    Eric,

    You're more than welcome to send it my way for evaluation. It wouldn't cost you anything. Shoot me an email and I'll give you my shipping info.

    [email protected]

    Thanks,

    Tyler
    We fix it all! Give us a call at 855-437-3497.
    Reply With Quote Reply With Quote
  5. 02-22-2016, 02:35 PM #5
    AiR_GuNNeR
    AiR_GuNNeR is offline Registered
    Join Date
    Feb 2010
    Posts
    371

    Re: Looking for a spindle driver board NM-145

    Thank Tyler,
    I think it is beyond repair. The micro is toasted. I was debugging a problem with my probe and had a ground wire setup to do this. The wire slipped out of my grip and raked across the board with pretty dramatic consequences...
    Reply With Quote Reply With Quote
  6. 02-22-2016, 02:48 PM #6
    ies fixs
    ies fixs is offline Registered
    Join Date
    Apr 2012
    Posts
    84

    Re: Looking for a spindle driver board NM-145

    Quote Originally Posted by AiR_GuNNeR View Post
    Thank Tyler,
    I think it is beyond repair. The micro is toasted. I was debugging a problem with my probe and had a ground wire setup to do this. The wire slipped out of my grip and raked across the board with pretty dramatic consequences...
    Oh man. That doesn't sound good at all. Do you have a picture of it? I can show it to my techs and see what they say. We've had a ton of stuff come in here that others have said no to.
    We fix it all! Give us a call at 855-437-3497.
    Reply With Quote Reply With Quote
  7. 03-02-2016, 04:59 PM #7
    Krenovian
    Krenovian is offline Registered
    Join Date
    Oct 2011
    Posts
    61

    Re: Looking for a spindle driver board NM-145

    Quote Originally Posted by AiR_GuNNeR View Post
    I fried the spindle driver board on my NM-145 and would like to get up and running again ASAP. Anyone out there that retrofitted their mill willing to part with one? This is the small daughter board that mounts to the spindle power board.
    Eric
    I've retrofitted my NM 145 mill. You are welcome to the boards and spindle motor for that matter if you can use them. PM me.

    Curtis

    Sent from my XT1094 using Tapatalk
    Reply With Quote Reply With Quote
  8. 03-07-2016, 02:04 AM #8
    AiR_GuNNeR
    AiR_GuNNeR is offline Registered
    Join Date
    Feb 2010
    Posts
    371

    Re: Looking for a spindle driver board NM-145

    Props to Curtis who set me up with his old hardware. I'm up and running this weekend. May good karma settle upon your household!
    Eric

    Quote Originally Posted by Krenovian View Post
    I've retrofitted my NM 145 mill. You are welcome to the boards and spindle motor for that matter if you can use them. PM me.

    Curtis

    Sent from my XT1094 using Tapatalk
    Reply With Quote Reply With Quote
  9. 03-07-2016, 09:51 PM #9
    Krenovian
    Krenovian is offline Registered
    Join Date
    Oct 2011
    Posts
    61

    Re: Looking for a spindle driver board NM-145

    Thanks Eric. Glad the board worked for you.

    Curtis

    Sent from my XT1094 using Tapatalk
    Reply With Quote Reply With Quote
  10. 03-12-2016, 04:31 AM #10
    3000
    3000 is offline Registered
    Join Date
    Dec 2009
    Posts
    4
    i have a nm145 that I would like to sell.
    If anyone is looking for one, email me at [email protected]
    Comes with coolant tank, 4th axis connection and tooling.
    Dar
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. G0704 stock spindle control board to mach 3 via C32 board.
    By ballistic42 in forum Benchtop Machines
    Replies: 13
    Last Post: 09-22-2016, 02:47 AM
  2. Help deciding which breakout board or driver board etc to use!
    By localbroadcast in forum Servo Motors / Drives
    Replies: 7
    Last Post: 06-09-2016, 09:25 PM
  3. Home switch for CNC 3020T- with a Spindle Control Board, JP-382A and JP-1482 Board
    By Terrynf in forum PCB milling
    Replies: 0
    Last Post: 11-30-2014, 05:16 AM
  4. Replacing TB6560 driver board's driver chip. Is it possible?
    By Moodaguda in forum CNC Machine Related Electronics
    Replies: 4
    Last Post: 08-07-2013, 09:02 AM
  5. different version spindle driver board
    By david_geng in forum Syil Products
    Replies: 3
    Last Post: 09-07-2007, 12:08 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules