[mengi]

Hi
My machine is multicam 1000 series wood cut
please i need help, this problem happens while am doing warming up for spindle then timer in the control show 5:21 and control forzed, i turned machine off by mail switch and then i turned it again showed this message in the control LCD.
please how can i fix it :,( :drowning:

message in the picture and also video form inside the cabinet
https://youtu.be/bvbBSyi_cLI
thanks,

[MCPservice]

Give me a call....need more information.....
678-548-1483
Maurice

[mengi]

am not in US now, please can i contact you on Skype please, if yes please give me your Skype ID.

[mengi]

i sent you SMS

[MCPservice]

sorry don have a Skyp account, that a pic and post of your control cabinet. Also when you home out the machine, the inverter comes on with out any fault correct?

[mengi]

yes you are right the inverter comes on with out any fault, i think the problem with setting ,is there any setting or file i must put it inside Motion Control or something like that?

take a look to the pic in the attchment

[mengi]

sorry don have a Skyp account?

please do you have any way to meet you online , facebook,yahoo messanger etc.....?

[MCPservice]

Cant be the inverter is programmed internally, and should not change. Plus the spindle warm up is a internal program to the controller not motion control. When you request the spindle warm up, what shows up on the keypad.

- - - Updated - - -

yes but I am about to get on a flight.....it will be Monday before I am available after 12 today eastern

[mengi]

Cant be the inverter is programmed internally, and should not change. Plus the spindle warm up is a internal program to the controller not motion control. When you request the spindle warm up, what shows up on the keypad.

its showed timer down 5min
after u pressed enter to warm up the keypad showed warming up 6000 RPM and timer suddenly freeze at 4min:21sec ,then i shutdown the machine from main switch and turned it again showed that message (KDM20 v1.37) , but when when i pressing the arrow key spindle is moving and the machine get the order from keypad but the information not showed in keypad LCD just (KDM20 v1.37) nothing else.

yes but I am about to get on a flight.....it will be Monday before I am available after 12 today eastern

ok

[MCPservice]

What is your incoming power are you single or three phase. Then check to see how your transformer is tapped, if your voltage is lets say 212 then transformer should be tapped for 208, the 1000 series machine were always like to be tapped lower on the transformers.

[mengi]

What is your incoming power are you single or three phase. Then check to see how your transformer is tapped, if your voltage is lets say 212 then transformer should be tapped for 208, the 1000 series machine were always like to be tapped lower on the transformers.

ok but now how i can get keypad information show in keypad LCD again

[MCPservice]

????? did you drop the keypad or is the cable damaged in any way....

[mengi]

????? did you drop the keypad or is the cable damaged in any way....

NO

[MCPservice]

So when you turn on the machine, nothing shows up on the keypad correct?

If you go thru the process of homing the machine, does it still hard home the machine, and if it does that can you use the directional keys and it still moves the machine.

[mengi]

So when you turn on the machine, nothing shows up on the keypad correct?
no, but its only showing KDM20 V1.37 SN=7356 on the keypad display

If you go thru the process of homing the machine, does it still hard home the machine, and if it does that can you use the directional keys and it still moves the machine.

yes its moving and going to home

[MCPservice]

Ok, the display is out. Unfortunately until Multicam starts accepting repairs again, your only alternative would be to buy a new or refurbished keypad.

[Marty8701]

I have the same problem on my 5000 series . It only shows (KDM20 V1.10SN=814. Can’t even move the machine any solutions

[MCPservice]

How old is your 5000?