[rappa]

hello!!!

i have the nvum v1.1 and it works, i think,

after all my nvum is not work correct!!!! the probe is not work properly and the controller fail steps, the z moves is very fault....the jog and the home limits is work. i dont understand.... i will put the nvum in the side, what controller should i buy?????

[carl1961]

after all my nvum is not work correct!!!! the probe is not work properly and the controller fail steps, the z moves is very fault....the jog and the home limits is work. i dont understand.... i will put the nvum in the side, what controller should i buy?????

Rappa, I put my ver2 aside too, there not reliable, very bad programming. I went with a C11GS and use the UC100 USB to pararell controller, everything is running great.

Sent from my Nexus 6 using Tapatalk

[Masterdrive]

i will put the nvum in the side, what controller should i buy?????

Rappa, I put my ver2 aside too, there not reliable, very bad programming. I went with a C11GS and use the UC100 USB to pararell controller

Same for me...
couple of posts ago I've documented my findings with the V2... many problems mostly related to probing, limits, general movement

My V2 will be sent back once the new controller has arrived.
I will use a UC300ETH from now on... lots of IO options, and direct 0-10V output for controlling a VFD

[rappa]

Same for me...
couple of posts ago I've documented my findings with the V2... many problems mostly related to probing, limits, general movement

My V2 will be sent back once the new controller has arrived.
I will use a UC300ETH from now on... lots of IO options, and direct 0-10V output for controlling a VFD

you will use any board to pulgin the UC300? i want to buy a usb UC300 but should use a board to connect... like this one [VIDOE]https://www.youtube.com/watch?v=h6ea0L0j4zU[/VIDEO]

[mach-mate]

Please Check our New 10" Touch Screen CNC Controller - Made in UK

Kickstarter Link below

https://www.kickstarter.com/projects...oject&term=cnc

You Tube Link below

https://www.youtube.com/watch?v=Z6soNUxN900&t=118s

Some Photos Below

[Masterdrive]

The UB1 definitely is one of the nicest boards to use with the UC300
Unfortunately, it's also one of the most expensive ones.

I will use a couple of cheaper boards connected to the 5LPG board (a DB25-1205, a ST-V2, and a C10S)
Most of these already came along with my stepper motors, the C10S was a bargain a Eb**

[Grubma]

Hi folks, I'am new at this forum. I have purchased a NVEM motion control card. I'd like to use it for my laser engraver machine. My laser is wired to the spindle out of the controller. The motion controller ignore spindle settings at Mach3 and it's takes a long time to spin up and down so my laser doesn't work properly when I use M3 SXXX and M5 commands.
Is it possible to turn off spin up and down delays of the motion controller?
Thanks in advance.

[rick.willow]

NVEC400 controller card

hi guys

anybody got an email address for the manufacturer of this controller
can not get any thig working

regards

rick

[handyss]

hello!!!

i have the nvum v1.1 and it works, i think, but the speed off the motor is 1/2 off that i put in the motor parameter.... for example i put 2000mm/min in the motor tuning and it outputs, on the G0, 1000mm/min, any one can help???? sorry for my bad English.

Hello. I am Spanish. And I have the same version. Please contact me on [email protected]. Best regards

[wordperfect]

Hi
I received NVEM ver1 controller and I could not run stepper motors, only DRO in Mach3 moving, but all other signals works
I encountered the same problem without answers
https://www.cnczone.com/forums/contr...ml#post1998278

Everything was done according to the instructions, so I tried everything I knew,
Note: drivers and motors work with another controller

Does anyone know anything about this, and how to solve this problem?
Help please
Best regards

[ahrihz]

hi milky could send me also the link for NVEM Driver _P (Released 23/05/2017)

appreciate milky. cheers

[rognets]

Hello All

I wish I had read this post more thoroughly before I purchased my NVEM. Have just spent 5 days rebuilding my cnc machine, It was well overdue after nearly 10 years of use. Thinking that the nevm would be the latest and hopefully better stepper controller.

Many grey hairs and frustration at the randomly changing inputs, outputs and drive directions. Completely rewired the machine knowing that I have had some issue at times with rf feedback. Thought I had that covered but maybe not?

The machine is running now, but I have not been able to resolve the random home/limits set up, have decided to just run with the limits with no homing.

The smoothstepper is really good when it runs, lots of power and smooth quiet operation.

I have developed a deep distrust for the selling countrymen, I purchased through DHGate, I found them deceptive and rude, I will be closing my account after I consider if the NVEM is actually going to work with Mach3?

Regards

[Waz]

Glad I read this have had the same issues. Ran fine for a few weeks then began to glitch. Will try re installing everything and see how I go.

[rognets]

Hi milky
I would very much appreciate the new dll, I have resolved all my NVEM issues and only the home / limit issue remains, If this DLL fix's that problem then NVEM may be OK?????

[jlambier]

I'm thinking about getting one of the NVEM cards and I'm hoping that someone who has used the card could tell me whether the spindle index function works. The manual shows that there is a port labelled as Index but the example of how to connect it doesn't show it being used. Also, the Lollette site says "Nvem does not support spindle speed feedback?INDEX)" but this isn't mentioned on AliExpress. It seems odd to have a connection that is labelled as Index but state that it doesn't have this function.

Thanks for any input,
Jim

[carl1961]

I'm thinking about getting one of the NVEM cards and I'm hoping that someone who has used the card could tell me whether the spindle index function works. The manual shows that there is a port labelled as Index but the example of how to connect it doesn't show it being used. Also, the Lollette site says "Nvem does not support spindle speed feedback?INDEX)" but this isn't mentioned on AliExpress. It seems odd to have a connection that is labelled as Index but state that it doesn't have this function.

Thanks for any input,
Jim

If you want a dependable cnc card don't buy this company stuff, I have a NVUM sitting on the shelf now because no firmware updates to fix homing issues. I went to CNC4PC and bought the c11s and never had any issues. The CNC4PC should have eithernet cards too.

Sent from my Nexus 6 using Tapatalk

[OlfCNC]

You can get a UC400ETH or UC300ETH and some cheap breakout boards from CNC4PC for similar cost as the NVUM and at least those work.

[Aberun]

Hi everyone

Im totally new in CNC world, and as you may guessed I bought a NVEM v2 BoB.
took me probably 4 hours to get it working but now I have control on my steppers
but I can understand how to connect to a spindle
I have Huayang 2.2kw inverter and I have no clue how to wire that thing
spindle is now connected to inverter and works fine, now I need a connection between inverter and BoB
can someone please help me out with that ?

[aqualovec]

Hi everyone

Im totally new in CNC world, and as you may guessed I bought a NVEM v2 BoB.
took me probably 4 hours to get it working but now I have control on my steppers
but I can understand how to connect to a spindle
I have Huayang 2.2kw inverter and I have no clue how to wire that thing
spindle is now connected to inverter and works fine, now I need a connection between inverter and BoB
can someone please help me out with that ?

Not understand BoB please explain your controller board ?

[asuratman]

Maybe only chinese can install nvew ... Its proven already their industry work !!!