524,059 active members*
2,279 visitors online*
Register for free
Login
Page 3 of 3 123
Results 41 to 59 of 59
  1. #41
    Registered
    Join Date
    May 2018
    Posts
    2

    Re: Tria 7500 for Morbidelli Author 503

    do you by any chance have a plc disk for Morbidelli Author 503?

  2. #42
    Registered
    Join Date
    Nov 2009
    Posts
    6

    Re: Tria 7500 for Morbidelli Author 503

    Hi all,

    I need help please. I am setting the PLC's on an Author 503, I have the disks and steps. The password "MORBI" let me do most of the installation, but when I do step 5( 5-INSERT PARAMETER'S DISK, EDITOR, PARAMETERS, LOAD ALL) and press the "EDITOR" button I get an error message "PASSWORD NOT RECOGNIZED". Does anybody know what password is needed for this step. SCM Australia is just ignoring my request for help.

    Any help will be greatly appreciated.

    Thanks

    Piet

  3. #43
    Member
    Join Date
    Feb 2006
    Posts
    14

    Re: Tria 7500 for Morbidelli Author 503

    Quote Originally Posted by cncpiet View Post
    Hi all,

    I need help please. I am setting the PLC's on an Author 503, I have the disks and steps. The password "MORBI" let me do most of the installation, but when I do step 5( 5-INSERT PARAMETER'S DISK, EDITOR, PARAMETERS, LOAD ALL) and press the "EDITOR" button I get an error message "PASSWORD NOT RECOGNIZED". Does anybody know what password is needed for this step. SCM Australia is just ignoring my request for help.

    Any help will be greatly appreciated.

    Thanks

    Piet
    before loading the PLC parameters you need
    enter another password
    I have an Author A504, and last week I had to load all the parameters again

  4. #44
    Registered
    Join Date
    Nov 2009
    Posts
    6

    Re: Tria 7500 for Morbidelli Author 503

    Quote Originally Posted by Baldo View Post
    before loading the PLC parameters you need
    enter another password
    I have an Author A504, and last week I had to load all the parameters again
    Thanks for your reply Baldo. I did enter the two part number code if that is what you mean. The system let me do all the steps up to the "EDITOR" button is pressed. I tried redoing from the start a few times and every time at the "EDITOR" button I get the same response from the system.

  5. #45
    Registered
    Join Date
    Nov 2009
    Posts
    6

    Re: Tria 7500 for Morbidelli Author 503

    Hi all,

    I found the issue. The two part back door password I had was for the wrong version of tria. I hope this help somebody else in future

    Passwords are as follows

    TRIA7500 REL.38.2.XX.X - 1194121 (SPACE) 1195457
    TRIA7500 ReL.38.2.XX.1 - 1229049 (SPACE) 1195457
    TRIA7500 REL.38.1.XX.X - 1193479 (SPACE) 1195457
    TRIA7500 REL.38.3.XX.1 - 1189527 (SPACE) 1195457


    Good luck

    Piet

  6. #46

    Join Date
    Jan 2019
    Posts
    5

    Re: Tria 7500 for Morbidelli Author 503

    can you send me by mail the plc file of 503?

  7. #47

    Join Date
    Jan 2019
    Posts
    5

    Re: Tria 7500 for Morbidelli Author 503

    can you send me the plc file of morbidelli 503 ? place eranmonfort3@gmail.com

  8. #48
    Junior Member
    Join Date
    Feb 2019
    Posts
    4
    Hi Sir,
    I have morbidelli 504 and plc failed.
    please, can you send me steps and all files to load plc.
    my mail is elhoteby.khaled@yahoo.com

    regards,
    khaled

  9. #49
    Junior Member
    Join Date
    Feb 2019
    Posts
    4
    Quote Originally Posted by cncpiet View Post
    Hi all,

    I found the issue. The two part back door password I had was for the wrong version of tria. I hope this help somebody else in future

    Passwords are as follows

    TRIA7500 REL.38.2.XX.X - 1194121 (SPACE) 1195457
    TRIA7500 ReL.38.2.XX.1 - 1229049 (SPACE) 1195457
    TRIA7500 REL.38.1.XX.X - 1193479 (SPACE) 1195457
    TRIA7500 REL.38.3.XX.1 - 1189527 (SPACE) 1195457


    Good luck

    Piet
    where I can find the version?

  10. #50
    Junior Member
    Join Date
    Feb 2019
    Posts
    4
    Quote Originally Posted by stoned View Post
    Hey Ronnieworks.
    I have got both code and procedure to load plc files agin. If i get your mail address i will send it to you as attached word file. You probartly forgooten to renew the back up battery, i tried it myself.
    Best regards: Stoned
    Hi Sir,
    I have morbidelli 504 and plc failed.
    please, can you send me steps and all files to load plc.
    my mail is elhoteby.khaled@yahoo.com

    regards,
    khaled

  11. #51
    Member
    Join Date
    Feb 2019
    Posts
    3
    Hi all,
    We have recently purchased a Morbidelli 504 with a Tria 7500 and it seems that the parameters of the PLC have been lost as it says PLC is blocked (the backup battery is flat). We also have no disks for the machine. If someone could please send through the PLC code and loading procedure for the 504 to cameron@ccrv.com.au it would be greatly appreciated.

    Kind Regards,
    Cameron

  12. #52
    Member
    Join Date
    Apr 2019
    Posts
    1
    Hi,
    I have Morbidelli author 510 with a Tria 7500, and i need restore PLC and parameters, because battery is dead. I don't have disks for this machine.
    i would be greatly appreciated if someone could please send through the PLC code and loading procedure for the 510 to gccp05@gmail.com
    thanks
    Gil

  13. #53
    Member
    Join Date
    Sep 2019
    Posts
    3
    Quote Originally Posted by cncpiet View Post
    Hi all,

    I found the issue. The two part back door password I had was for the wrong version of tria. I hope this help somebody else in future

    Passwords are as follows

    TRIA7500 REL.38.2.XX.X - 1194121 (SPACE) 1195457
    TRIA7500 ReL.38.2.XX.1 - 1229049 (SPACE) 1195457
    TRIA7500 REL.38.1.XX.X - 1193479 (SPACE) 1195457
    TRIA7500 REL.38.3.XX.1 - 1189527 (SPACE) 1195457


    Good luck

    Piet
    Hi everybody!

    I have a A504 Rapid and I almost got everything back after battery gone dead. I get the "USER UNKNOWN" when I try to enter the editor. I tried the back door password for my version of TRIA but it still says "USER UNKNOWN".
    Any ideas?

    Regards
    KJ

    Edit:
    Found a simple solution that I just started the plc with run/stop and all of a sudden I can go into the editor and load parameters and everything.
    Last edited by kallejojje; 09-16-2019 at 02:35 PM.

  14. #54
    Member
    Join Date
    Oct 2019
    Posts
    3
    Quote Originally Posted by Baldo View Post
    I sent to you the Steps to load PLC data in AUTHO504

    By Email..
    please help me
    I buy morbidelli author 504.Plc batery was gone,I dont have plc floppy disc

    .Can you help me?Can you send me parameters for plc or any help.
    Nhuttruong.pd@gmail.com

  15. #55
    Member
    Join Date
    Oct 2019
    Posts
    3
    Quote Originally Posted by Baldo View Post
    before loading the PLC parameters you need
    enter another password
    I have an Author A504, and last week I had to load all the parameters again
    Do you have a morbidelli author 504 password?

  16. #56
    Member
    Join Date
    Oct 2019
    Posts
    3
    Quote Originally Posted by Baldo View Post
    before loading the PLC parameters you need
    enter another password
    I have an Author A504, and last week I had to load all the parameters again
    please help me
    I buy morbidelli author 504.Plc batery was gone,I dont have plc floppy disc

    .Can you help me?Can you send me parameters for plc or any help.

  17. #57
    Member
    Join Date
    Jun 2020
    Posts
    2

    Re: Tria 7500 for Morbidelli Author 503

    Hey guys, I am glad everybody's problems have been solved.
    Now it's my turn. Could someone please help me wake-up my 503 author?
    I need the plc and parameter files plus the instructions.
    Thanks in advance for the help, I appreciate it.I
    Apprenticejim@gmail.com
    Thanks

  18. #58
    Member
    Join Date
    Jun 2020
    Posts
    2

    Re: Tria 7500 for Morbidelli Author 503

    Hi stoned, could you p!ease help me too,
    I have to wake up my 503 and need the old and parameter file.
    And also the instructions thanks very much in advance.
    Apprenticejim@gmail.com

  19. #59
    Member
    Join Date
    Jun 2020
    Posts
    2

    Re: Tria 7500 for Morbidelli Author 503

    Hello Baldo, i need your help, if you steel have the file on the disk could you send a copy to my email adress pjitar@gmail.com, as i got battery gone. Thank you!

Page 3 of 3 123

Similar Threads

  1. Tria 7500
    By num1040 in forum CNC Machining Centers
    Replies: 2
    Last Post: 11-30-2019, 03:12 PM
  2. morbidelli 504 tria 7500
    By rprman1 in forum Commercial CNC Wood Routers
    Replies: 24
    Last Post: 09-14-2019, 06:04 PM
  3. Morbidelli Author 503 (1995) Tria 7500
    By num1040 in forum CNC Machining Centers
    Replies: 2
    Last Post: 03-05-2014, 03:42 PM
  4. TRIA 7500 software missing
    By pablogvivo in forum Controller & Computer Solutions
    Replies: 0
    Last Post: 01-07-2014, 09:45 AM
  5. 'Errore Generico' Morbidelli tria 7500
    By fmorandini in forum Maintenance DIY Discussion
    Replies: 0
    Last Post: 11-03-2013, 06:48 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •