Can anyone help me out on this problem? I need to have a remote on off.
Results 1 to 8 of 8
-
05-18-2017, 02:48 PM #1
Registered
- Join Date
- Jul 2016
- Posts
- 6
Huanyang 7.5 kw VFD help wiring remote start
-
05-22-2017, 08:45 PM #2
Registered
- Join Date
- Jun 2003
- Posts
- 866
Re: Huanyang 7.5 kw VFD help wiring remote start
you mean pushbuttons, correct?
You just want to go in one direction?
What kind of buttons, momentary?
-
05-22-2017, 08:52 PM #3
Registered
- Join Date
- Jul 2016
- Posts
- 6
Re: Huanyang 7.5 kw VFD help wiring remote start
Yes Push buttons. 1 button is ON and the other is OFF. And yes they are Momentary.
-
05-22-2017, 08:56 PM #4
Registered
- Join Date
- Jul 2016
- Posts
- 6
Re: Huanyang 7.5 kw VFD help wiring remote start
I had a 4.0 KW VFD. I had them hooked up to DCM and Forward. Now I went with a Bigger motor so I went with the 7.5 KW VFD.
-
05-22-2017, 09:07 PM #5
Registered
- Join Date
- Jun 2003
- Posts
- 866
Re: Huanyang 7.5 kw VFD help wiring remote start
my guess is that it is the same. The manual I have goes from 1/3 hp to 75 KW.
Page 37 in the manual at this link
Top diagram with run/stop. Ignoring the reverse button, wire it up that same way
-
05-22-2017, 09:20 PM #6
Registered
- Join Date
- Jul 2016
- Posts
- 6
Re: Huanyang 7.5 kw VFD help wiring remote start
-
05-22-2017, 10:04 PM #7
Community Moderator
- Join Date
- Dec 2003
- Posts
- 24220
Re: Huanyang 7.5 kw VFD help wiring remote start
I would hazard a guess that the S1 to S7 is the same as the previous version for the PLC inputs, these would be assigned in the parameters.
There should be much more in the manual than you show.
Al.CNC, Mechatronics Integration and Custom Machine Design
“Logic will get you from A to B. Imagination will take you everywhere.”
Albert E.
-
05-23-2017, 01:40 AM #8
Registered
- Join Date
- Jun 2003
- Posts
- 866
Re: Huanyang 7.5 kw VFD help wiring remote start
I take it you meant to post different pages rather than many copies of page 12?
Not sure why they would change the designations. I thought mine was the new version.
Reply With Quote
Similar Threads
-
Which is correct way to wire up a Powermax45 for remote CNC start
By jerryrigge in forum Waterjet General TopicsReplies: 3Last Post: 02-12-2010, 02:41 AM -
Remote Cylce Start and stop button
By R.DesJardin in forum Tormach Personal CNC MillReplies: 22Last Post: 04-10-2009, 02:09 AM -
Remote cycle start
By REVCAM_Bob in forum FanucReplies: 6Last Post: 03-19-2007, 01:08 AM -
Hypertherm remote start with hand torch?
By Drad98 in forum Community Club HouseReplies: 0Last Post: 01-27-2007, 03:22 AM -
Remote cycle start?
By REVCAM_Bob in forum FanucReplies: 0Last Post: 01-20-2007, 05:59 PM
Tags for this Thread
Posting Permissions
