585,668 active members*
4,216 visitors online*
Register for free
Login

Thread: RFQ Aluminum pulley flanges

Results 1 to 6 of 6
  1. 03-20-2007, 06:26 PM #1
    kmcwhq
    kmcwhq is offline Registered
    Join Date
    Oct 2005
    Posts
    105

    RFQ Aluminum pulley flanges

    I need someone to cut out flange rings from aluminum.

    Specs:


    ****NOTE: OD is 3.75 NOT 3.5 inches****

    6061T6 Alum.
    Thickness .060
    OD 3.75 inches (was 3.5)
    ID 2.450 +/-.015
    OD and ID must run concentric within .015
    OD and ID must be round within .015.
    Flat within .010.
    Quantities: 10/25/50 pcs
    Quote price & delivery including shipping
    Required ASAP.

    Email direct if possible....
    [email protected]

    Dan K
    Reply With Quote Reply With Quote
  2. 03-20-2007, 06:51 PM #2
    ddprecision
    ddprecision is offline Registered
    Join Date
    Apr 2005
    Posts
    86
    never mind...
    Reply With Quote Reply With Quote
  3. 03-21-2007, 03:52 AM #3
    kmcwhq
    kmcwhq is offline Registered
    Join Date
    Oct 2005
    Posts
    105
    More Info:

    Tolerances:

    Thickness: +/- .015 inches
    OD: +/-.030

    NOTE:

    OD is 3.75 NOT 3.5......

    My mistake!

    thanks
    dk
    Reply With Quote Reply With Quote
  4. 03-21-2007, 08:32 PM #4
    kmcwhq
    kmcwhq is offline Registered
    Join Date
    Oct 2005
    Posts
    105
    RFQ closed.

    Thanks
    Reply With Quote Reply With Quote
  5. 03-22-2007, 02:25 PM #5
    SteelCutter
    SteelCutter is offline Registered
    Join Date
    Oct 2006
    Posts
    31

    closed RFQ

    Was this job awarded to this community or was it pulled?
    Just curious!
    (nuts)(nuts)
    SteelCutter
    Reply With Quote Reply With Quote
  6. 03-22-2007, 03:20 PM #6
    kmcwhq
    kmcwhq is offline Registered
    Join Date
    Oct 2005
    Posts
    105
    Due to time constraints, it was done in house.
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. :RFQ: 2 304SS Flanges
    By CarTunr22 in forum Employment Opportunity
    Replies: 2
    Last Post: 03-06-2007, 04:48 AM
  2. Cutting side flanges off of Kurt-type vise?
    By InspirationTool in forum Work Fixtures / Hold-Down Solutions
    Replies: 8
    Last Post: 01-05-2007, 07:43 PM
  3. Bonding flanges to a timing pulley?
    By Chris D in forum Welding Brazing Soldering Sealing
    Replies: 8
    Last Post: 10-01-2005, 02:37 PM
  4. Machining exhaust flanges
    By pauls in forum MetalWork Discussion
    Replies: 8
    Last Post: 03-15-2005, 06:12 PM
  5. Aluminum Timing Pulley Supplier??
    By hddjohns in forum Community Club House
    Replies: 3
    Last Post: 08-09-2003, 12:33 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules