[fairfieldmw]

Im currently doing a search on the fagor alarm1057 ( sub-routine ) that is preventing me from homing the machine , it use to home then i deleted 3 part files that i had created and sent to cnc from windnc . Ever since then , i get a 1057 alarm . Odd ......& some how I have 2 of those files i deleted on my desktop screen .

Before I got myself involved with alarm 1057 , i was on the phone with the folks at bobcad ( mike , darren and cody ) and ( Yuli and Mohit ) Fagor canada . Bobcad guys are having a problem connecting predator to fagor with no results . After i downloaded windnc and got cody from bobcad on it we started to see some files arriving at cnc .
Fagor canada has insisted that the part files be in 6 digit .pim format and we did that . Only some ( not all ) would show up at cnc . Moreover , these files wouldn't run . first was a x axis ( softlimit ) alarm , Fagor said to take G54 out of the code & so I was presented with a y axis ( soft limit ) alarm after that .

My knowledge of cnc is limited , my knowledge of cad/cam consists of 227 mind numbing bobcad/cam training videos , i understand the basics of electrical and plc and this is the first machine of 3 im trying to bring online in my garage .

Too cheap to hire someone to do er , im getting the feeling that this is going to be a very educational experience .

This being my first post , Id like to say hello ......the gentlemen at bobcad had alot of nice things to about this board

Regards
Scott

[fairfieldmw]

alarm 1057 is gone and back to the original problem

heres the part bobcad sent
%SCOTT TEST SQUARE.PI,MX--,
N1 G90 G80 G70 G40 G17
N2 G51E0.0893B45
;(Machine Setup - 1-Feature 2 Axis-Profile Finish)
;(FEATURE 2 AXIS)
N3 T1
N4 S3880 M03
N5 G53
N7 G00 X0. Y0.
N8 G43 Z1. D1
N9 M08
N10 Z0.2
N11 Z0.1
N12 G01 Z-0.25 F22.3148
N13 Y2.5 F44.6296
N14 X2.5
N15 Y0.
N16 X0.
N17 G00 Z0.2
N18 Z-0.15
N19 G01 Z-0.5 F22.3148
N20 Y2.5 F44.6296
N21 X2.5
N22 Y0.
N23 X0.
N24 G00 Z0.2
N25 Z-0.4
N26 G01 Z-0.75 F22.3148
N27 Y2.5 F44.6296
N28 X2.5
N29 Y0.
N30 X0.
N31 G00 Z0.2
N32 Z-0.65
N33 G01 Z-1. F22.3148
N34 Y2.5 F44.6296
N35 X2.5
N36 Y0.
N37 X0.
N38 G00 Z0.2
N39 Z1.
N40 M09
N41 M05
N42 G0G53Z0
N43 G0G53X0Y0
N44 M30


Im getting alarm 1155 x axis soft llimit over run . The fact that i zero my table in the center , try and run a part , return to the XYZ axis screen and values are back to " home position " zero values is troubling .

any ideas ?

There are some existing programs on fagor that were generated at HMI , those part programs work as they should without any alarms .

thanks

[CAN MACHINE]

Did you ever get this resolved? I'm having similar issues. Did you get a proper post from BobCad?