[hiki4026]

Help me!

I am a total beginner of CNC
In my guess, I feel that the connection from the motor drive to the VFD is not going well.
Can you tell me how you solved it?

Current status
• Completed wiring and assembling everything according to the manufacturer's instructions.
-It was possible to operate Mach3 and move it manually in the X-axis / Y-axis / Z-axis direction.
? I was able to complete the commissioning when I made VFD and spindle independent.
? I switched PD001 / 002 to 1 which is the VFD setting
? When the motor drive (Soigeneris STDR-4C) and the VFD are connected by wiring, the VFD power lamp does not turn ON.
The voltage of the VFD input power supply was measured by a tester, but the voltage is zero.

environment
Home power: 100V 15A 60Hz
Machine: Routakit HD
PC: Windows 10 (Mach 3)
MotorDriver: SoigenerisSTDR-4C (EthernetSmoothStepper / GeckoDriveG540)
VFD: Huanyang Hy01D511B


I have been troubled for more than a month on this issue and have not advanced.
I want you to help me.
May I have a reply?

[mactec54]

Help me!

I am a total beginner of CNC
In my guess, I feel that the connection from the motor drive to the VFD is not going well.
Can you tell me how you solved it?

Current status
• Completed wiring and assembling everything according to the manufacturer's instructions.
-It was possible to operate Mach3 and move it manually in the X-axis / Y-axis / Z-axis direction.
? I was able to complete the commissioning when I made VFD and spindle independent.
? I switched PD001 / 002 to 1 which is the VFD setting
? When the motor drive (Soigeneris STDR-4C) and the VFD are connected by wiring, the VFD power lamp does not turn ON.
The voltage of the VFD input power supply was measured by a tester, but the voltage is zero.

environment
Home power: 100V 15A 60Hz
Machine: Routakit HD
PC: Windows 10 (Mach 3)
MotorDriver: SoigenerisSTDR-4C (EthernetSmoothStepper / GeckoDriveG540)
VFD: Huanyang Hy01D511B


I have been troubled for more than a month on this issue and have not advanced.
I want you to help me.
May I have a reply?

Post some photos of the wiring

[hiki4026]

Thank you for your reply!
Attach multiple images.

[mactec54]

Thank you for your reply!
Attach multiple images.

What is this part need some better photos, it seems your wiring is not correct in this area but can not tell from the photos, the main input power supply is going where

[hiki4026]

Thank you for reply!
Attach multiple images.

I'm sorry I'm confusing because the attached image is a dark room. Currently this is night.

I also attached an explanatory image.
Do you understand this?

By the way, the wiring in this inverter is not what I did.
The finished product has arrived.

[mactec54]

Thank you for reply!
Attach multiple images.

I'm sorry I'm confusing because the attached image is a dark room. Currently this is night.

I also attached an explanatory image.
Do you understand this?

By the way, the wiring in this inverter is not what I did.
The finished product has arrived.

Ok you can not switch the output of the VFD Drive to the Spindle

The Switch should be before the Filter on the incoming power and the neutral should not be switched only the Power Live wire should be switched

The out put from the filter should go direct to the VFD Drives input Power R and T terminals and Ground / Earth to the Ground / Earth Terminal

The VFD Drive output power 3Phase then goes direct to the Spindle and needs to be a 4 wire shielded cable 3 Hot / Live wires and Ground /Earth wire

If you only have 100v 15A I don't think that is going to work very well, where are you located