[im101]

Hi All,
Could anyone advise or know of any very cheap software to program a Trumpf 240 cnc punch (non rotation)

Many thanks

im101:bs:

[txcncman]

Free would be better. But it has to be good.

[dboland]

I wrote a DOS Program for the 240 some 25 years ago. It still works in XP Compatability Mode. It outputs the grapic part code for the 240.

Here is what that looks like:
(DFS,G 4468,GRAPHIC ,RWED)
G+19.100000384+1+29.141000752+0.0+3+5+1+0.218+0.21 8+1+0.0+1+0.14+0.14+1+0.0+3+0.125+1.0+1+0.0+3+2.93 7000064+0.125+1+0.0+3+1.0+0.156+1+0.0+0+21+0+1+1+0 +28.672000896+2.546999936+0+1+1+0+0.468999872+2.54 6999936+0+1+1+0+24.235000608+5.328000064+0+1+1+0+4 .891000768+5.328000064+0+2+1+0+14.69500064+4.26599 9792+0+3+1+5+29.079000472+1.957999936+29.079000472 +3.18199992+0.223999984+0+3+1+5+0.063001632+1.9579 99936+0.063001632+3.18199992+0.223999984+0+3+1+5+2 7.218999856+0.129999992+27.218999856+1.952999936+0 .822999936+0+3+1+5+1.922000896+0.129999992+1.92200 0896+1.952999936+0.822999936+0+3+1+5+27.218999856+ 3.187000032+27.218999856+5.510000224+0.661500096+0 +3+1+5+1.922000896+3.187000032+1.922000896+5.51000 0224+0.661500096+0+3+1+5+18.937999744+0.129999992+ 18.937999744+1.812999936+0.683+0+3+1+5+10.18700027 2+0.129999992+10.187000272+1.812999936+0.683+0+4+1 +5+27.152000432+5.578000064+1.989999744+5.57800006 4+2.778125056+0+4+1+5+27.152000432+0.062+19.006000 519+0.062+2.60449984+0+4+1+5+10.12000084+0.062+1.9 7400096+0.062+2.60449984+0+5+1+5+29.011001587+1.87 5+27.157001488+1.875+0.854000064+0+5+1+5+29.011001 587+3.276999936+27.157001488+3.276999936+0.8540000 64+0+5+1+5+0.130001072+1.875+1.984001024+1.875+0.8 54+0+5+1+5+0.130001072+3.265000112+1.984001024+3.2 65000112+0.854+0+4+1+5+19.0+1.75+10.125+1.75+1.979 333312+4+0.0+0.0+0+29.141000752+0.0+0+29.141000752 +5.640999808+0+0.0+5.640999808+0+29.141000752+5.64 0999808+0.055+0.03937008+0+1+0+0+M30

You can have it for free if you are interested. Let me know,

Dave

[email protected]

[njic]

Is it possible to use it on 260R ? Is there any free or cheap solution?

[Independent CNC]

If you only need a few programs I can generate them for a small cost. The software I am using would cost you around 5k.

Independent CNC Programmer

www.independentcnc.com

My mission is to share CNC programming innovations for a lifetime.

[njic]

Thank you for answer.

I can make (simple) programs on bosch control unit, but for serious production I need to get one of the softwares. I would like to find the most inexpensive solution for my trumpf TC260R, and it would be great if the same application can be upgraded to run water jet (which we plan to buy in future). I have tried Metalix software, but didn't have time to go deep into it.

Which software do you use? Did you mean 5k dollars?

[Mensur]

Hi All

I have bought a trumatic 240 non rotation machine i have a problem on it it dosent accpet the program from pc it shows me warning 149 i have checked the cable and everything it is ok can someone please give some advice what kind of problem it can have ???

Please contact me [email protected]

[JulioFranco]

I developed my own software for the Tc260R. It runs in windows and have a gráficas interface and some macros as windows with rounded corners, notches, lines of holes etc. If you’re interested this is my email [email protected]. It generates the code for the cc220 from Bosch and we have made several programs on it