584,841 active members*
4,329 visitors online*
Register for free
Login
IndustryArena Forum > Machine Controllers Software and Solutions > Mazak, Mitsubishi, Mazatrol > Mazak QT8N with T plus control- Power Help (please)
Results 1 to 6 of 6
  1. #1
    Join Date
    Jun 2013
    Posts
    25

    Mazak QT8N with T plus control- Power Help (please)

    Helping someone get a 1994 Mazak up and going again. It was supposedly running a few weeks ago, but you know how that goes. 3 phase power into the machine is good. Green start LED on front of control is lit. Red button is not. In the back cabinet, one of the small power supplies has a red LED on it and measure 24v. The other power supply is not lit up. I believe it receives its power from the main power supply board. This board is located with the other boards in a rack style setup. This board has nothing lit on it. I measured 50 volts going into the board. On the board, it says 100v IN.

    Does anybody have any information such as a power flow control chart? What about an electrical diagram for T-plus control. Where does the power supply board receive its power form?

    Thanks for the help!

  2. #2
    Join Date
    Jun 2013
    Posts
    25

    Re: Mazak QT8N with T plus control- Power Help (please)

    Small update. We were told is was running on 220volts. Pulled the cover off to verify lugs on transformer and I am not really sure what it was set on, but it was not 220v....We have action now. On to the next problem.

    Breaker QF12 trips immediately. Anybody point me in the right direction as to what that belongs to?

  3. #3
    Join Date
    Jun 2013
    Posts
    25

    Re: Mazak QT8N with T plus control- Power Help (please)

    QF12 breaker still pops

    Light on power supply has a red led lit up for AC fail... from what I have read, it can be caused by a few things. Low/High AC voltage....It reads 107 which is within range. Second option is short to ground on 24v power supplies. Voltages on power supplies look fine. Removed output wires from power supply, no change.

    Also, the KM21 main power supply contactor isn't pulled. At what point should that energize?

  4. #4
    Join Date
    Sep 2007
    Posts
    66

    Re: Mazak QT8N with T plus control- Power Help (please)

    Hi

    Did you solve this problem??

    greetings bertus

  5. #5
    Join Date
    Feb 2017
    Posts
    3

    Re: Mazak QT8N with T plus control- Power Help (please)

    No i did not, any suggestions?

    Thanks

    Sent from my SM-N960U using Tapatalk

  6. #6
    Join Date
    Sep 2007
    Posts
    66

    Re: Mazak QT8N with T plus control- Power Help (please)

    hi

    no i have same sort of problems
    maybe this link will help,

    MITSUBISHI MAZATROL T PLUS Maintenance Manual pdf - CNC Manual


    greetings bertus

Similar Threads

  1. Mazak QT8N barfeeder wiring Mazatrol T32-2
    By Taivo in forum Mazak, Mitsubishi, Mazatrol
    Replies: 0
    Last Post: 03-07-2018, 07:02 PM
  2. Mazak L Plus laser error 017 Power control limit!!!
    By contrabas in forum Laser Hardware
    Replies: 0
    Last Post: 08-24-2016, 09:39 AM
  3. Mazak L Plus laser error 017 Power control limit!!!
    By contrabas in forum Mazak, Mitsubishi, Mazatrol
    Replies: 0
    Last Post: 08-24-2016, 09:36 AM
  4. Mazak QT8N T32-2 Tool change position
    By PANagel in forum Mazak, Mitsubishi, Mazatrol
    Replies: 5
    Last Post: 08-01-2014, 03:25 PM
  5. MAZAK QT8N stopped with Alarm 039
    By ua6lfj in forum DNC Problems and Solutions
    Replies: 4
    Last Post: 10-09-2012, 01:49 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •