512,381 active members
3,384 visitors online
Register for free
Login
IndustryArena Forum > Commercial Products Support Forums > CNC4PC > I have a question, C11G breakout board CNC4PC $68.00
Results 1 to 6 of 6
  1. #1
    Registered
    Join Date
    Jan 2012
    Posts
    76

    I have a question, C11G breakout board CNC4PC $68.00

    Hi,
    If I have a older PC dedicated for the mill with a Parallel port , Will The C11G - Multifunction CNC Board CNC4PC sells for $68.00 would this be the only board I would need to run my mill? https://www.cnc4pc.com/c11g-multifun...cnc-board.html

    OR

    Would I still have to add UC300ETH - ETHERNET MOTION CONTROLLER $125 + mother board $29 and Cable with C11G breakout board?

    And last question will it work with mach3,uccnc, and linuxcnc?

  2. #2
    Registered
    Join Date
    Oct 2004
    Posts
    257

    re: I have a question, C11G breakout board CNC4PC $68.00

    Tell me more:
    - What are you using now?
    - What operating system?
    - What functions? features? are you running? wanting to have?
    The C11G is a basic breakout board but has all the major you may need. Like:
    - Spindle Control.
    - External Hardware Enable.
    - LEDs on all I/Os.
    - Built-in Pull-up/down resistors.
    - Spindle Control.
    - Relays.
    - Watchdog (Safety Charge Pump).
    If you want to use it with Win10/64 and Mach3/4 or UCCNC, you may just need to add a UC100 or other motion controllers, like the ESS or UC300ETH.

    Arturo Duncan
    https://cnc4pc.com

  3. #3
    Registered
    Join Date
    Jan 2012
    Posts
    76

    Re: I have a question, C11G breakout board CNC4PC $68.00

    Thanks,
    #1 QUESTION YES OR NO: Will The C11G - Multifunction CNC Board CNC4PC sells for $68.00 would this be the only board I would need to run my mill? https://www.cnc4pc.com/c11g-multifun...cnc-board.html

    And last question will it work with mach3,uccnc, and linuxcnc?

    Arturo i'm running closed loop steppers, say if something go wrong like loss of step the drive with have a alarm light on and is there a hookup on the board so it stops the program?

  4. #4
    Registered
    Join Date
    Oct 2004
    Posts
    257

    Re: I have a question, C11G breakout board CNC4PC $68.00

    This may be a little more complex. It should be doable, but we would need to get into the details of the circuit your stepper motors use to figure out how to wire and configure the logic for this.
    If you are using closed loop steppers, you may be better off using a multifunction board using the RJ45 connector boards. These RJ45 connector boards handle the wiring and logic for most drives making it easier to wire systems with feedback as they not just connect the step and direction signals, but also the fault and enable signals.
    In your case, maybe the C76 with the C34HS connector boards would be the solution:
    https://www.cnc4pc.com/c76-uc300-mul...ion-board.html
    https://www.cnc4pc.com/c34-for-hybrid-servo-drive.html
    Let me know if you have any questions.
    Arturo Duncan
    https://cnc4pc.com

  5. #5
    Registered
    Join Date
    Jan 2012
    Posts
    76
    Quote Originally Posted by arturod View Post
    This may be a little more complex. It should be doable, but we would need to get into the details of the circuit your stepper motors use to figure out how to wire and configure the logic for this.
    If you are using closed loop steppers, you may be better off using a multifunction board using the RJ45 connector boards. These RJ45 connector boards handle the wiring and logic for most drives making it easier to wire systems with feedback as they not just connect the step and direction signals, but also the fault and enable signals.
    In your case, maybe the C76 with the C34HS connector boards would be the solution:
    https://www.cnc4pc.com/c76-uc300-mul...ion-board.html
    https://www.cnc4pc.com/c34-for-hybrid-servo-drive.html
    Let me know if you have any questions.
    Arturo Duncan
    https://cnc4pc.com
    I like the C76 board is that all in one board?

  6. #6
    Registered
    Join Date
    Oct 2004
    Posts
    257

    Re: I have a question, C11G breakout board CNC4PC $68.00

    Yes... It has several options that are configurable on checkout. So you do receive one system.

    Arturo Duncan
    https://cnc4pc.com

Similar Threads

  1. C11G CNC Breakout Board cnc4pc
    By linx310 in forum Newly Posted Classifieds Listings
    Replies: 0
    Last Post: 12-21-2014, 09:07 PM
  2. Replies: 8
    Last Post: 07-31-2012, 12:47 AM
  3. CNC4PC C11G BOARD
    By MegaMoog in forum Benchtop Machines
    Replies: 1
    Last Post: 05-05-2010, 09:29 PM
  4. KL-B25 or C11g Breakout board?
    By technosteve in forum Automation Technology Products
    Replies: 1
    Last Post: 03-14-2009, 01:32 AM
  5. CNC4pc C23 breakout board
    By eloid in forum General CNC Machine Related Electronics
    Replies: 0
    Last Post: 02-07-2009, 02:49 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •