584,846 active members*
4,180 visitors online*
Register for free
Login
IndustryArena Forum > CNC Electronics > Stepper Motors / Drives > Does anyone know this stepper motor?
Results 1 to 10 of 10
  1. #1
    Join Date
    Apr 2015
    Posts
    4

    Does anyone know this stepper motor?

    I've looked everywhere. I can't find the datashet Do you have any guidance for me?

    Please
    Attached Thumbnails Attached Thumbnails IMG-20200325-WA0003.jpg  

  2. #2
    Join Date
    Nov 2013
    Posts
    4281

    Re: Does anyone know this stepper motor?

    Hi,
    what you you need from the spec sheet?

    Is there something about the stepper that you cannot measure or otherwise deduce?

    Craig

  3. #3

    Re: Does anyone know this stepper motor?

    It look llike that motor from China , do you want to get a new pcs one ?

  4. #4
    Join Date
    Nov 2013
    Posts
    4281

    Re: Does anyone know this stepper motor?

    Hi,

    It look llike that motor from China
    Rubbish, it is a two phase Vexta stepper made by Oriental Motor Co, Japan......its as good as stepper motors get.

    My mini-mill is powered by Vexta 5 phase steppers and ultra low lash planetary gear reductions and Vexta drives....all absolutely superb.

    Craig

  5. #5
    Join Date
    Apr 2015
    Posts
    4

    Re: Does anyone know this stepper motor?

    Thank you for your help.
    I need to change this engine, and I don't know which features to analyze for the purchase ..... What should be analyzed to buy an exactly identical engine

  6. #6
    Join Date
    Nov 2013
    Posts
    4281

    Re: Does anyone know this stepper motor?

    Hi,
    I need to change this engine, and I don't know which features to analyze for the purchase
    Why? Vexta steppers are class leading quality, if its not broken then is there need to change it?

    Steppers follow NEMA size recommendations. Is it a 17 size, 23 size, 34 size? By that I mean 1.7 (or 2.3 or 3.4) inch across the flats
    of the mounting flange? Thereafter just about any stepper will work. If you want to use it for CNC purposes and therefore want it to run
    fast then you MUST select a low inductance replacement.

    Craig

  7. #7
    Join Date
    Apr 2015
    Posts
    4

    Re: Does anyone know this stepper motor?

    The stepper motor is defective so I must replace it.
    But there are other parameters besides their dimensions, such as torque, phase, number of wires, pitch. Or not?

  8. #8
    Join Date
    Dec 2003
    Posts
    24216

    Re: Does anyone know this stepper motor?

    The spec's on the motor will get you started, volt/current , the No. of wires is 4 for Bi-polar, more than 4, Unipolar.
    I have the Vexta Cat. going back to 1994/95 but does not show that model.
    Al.
    CNC, Mechatronics Integration and Custom Machine Design

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.

  9. #9
    Join Date
    Apr 2015
    Posts
    4

    Re: Does anyone know this stepper motor?

    Thanks,,,, AL

    What characteristics should I observe to choose an equal step motor?

  10. #10
    Join Date
    Dec 2003
    Posts
    24216

    Re: Does anyone know this stepper motor?

    It is a little hard without knowing the full specs of the motor, but there are guides on the Gecko site that may be of help.
    Al.
    CNC, Mechatronics Integration and Custom Machine Design

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.

Similar Threads

  1. Connect an 8 wire stepper motor to a TB6560 Stepper motor driver
    By muldoon22 in forum Stepper Motors / Drives
    Replies: 2
    Last Post: 12-31-2016, 07:26 AM
  2. Replies: 0
    Last Post: 02-26-2013, 08:37 AM
  3. 6 leads stepper motor connect to TB6560AHQ stepper driver board
    By wf1318 in forum Stepper Motors / Drives
    Replies: 2
    Last Post: 07-25-2010, 08:19 AM
  4. Integrated stepper motor? with built-in stepper motor driver
    By uirobot in forum News Announcements
    Replies: 0
    Last Post: 06-07-2010, 09:59 AM
  5. Beltdrive-stepper motor-stepper motor driver
    By Georg in forum Stepper Motors / Drives
    Replies: 0
    Last Post: 10-16-2007, 10:56 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •