532,031 active members*
3,584 visitors online*
Register for free
Login
IndustryArena Forum > General Manufacturing Processes > Milling > Maho MH600E Error 0 23, I 05
Results 1 to 1 of 1
  1. #1
    Member
    Join Date
    Apr 2020
    Posts
    5

    Maho MH600E Error 0 23, I 05

    Anyone know how to solve error code ERR 0 23, I 05
    Philips 432

  2. #2

    Re: Maho MH600E Error 0 23, I 05

    I05 is normal until you power up the hydraulics , O 23 is an operator error that appears when you type something wrong at the controller. I am amazed that no one sims to replay anymore on this forum.

  3. #3
    Member
    Join Date
    Apr 2020
    Posts
    5

    Re: Maho MH600E Error 0 23, I 05

    Hi Thanks for the replay
    I manages to get rid of the O 23 error, the backup battery were dead so I had to enter all the constants again.
    I still have the I05 error and the hydraulic will not start only if I keep my finger on the button.
    I have tried to activate the switch for the axis end stop to see if switches for the axis is jammed, but I still have the error.

    Sorry for my late replay I am new in the forum.
    I have open a new thread with a picture I didn't know how to add a picture in this one.

  4. #4

    Re: Maho MH600E Error 0 23, I 05

    If the limit switches are clear than you should know that there is a technique for powering one the hydraulics. Firs if the machine has sat over night , press the hydraulic switch for a couple of seconds to build up pressure. Than the procedure it self is to keep the hydraulic button pressed for a second ore two with one hand than immediately after depressing it press the CLEAR button. Normally the OPENLOOP will be gone and the machine will work.

  5. #5
    Member
    Join Date
    Apr 2020
    Posts
    5

    Re: Maho MH600E Error 0 23, I 05

    I tried what you recommended but hydraulic stop when I release the button, and I have the error that is showed on the picture.
    When I tri to start, all the safety gates are closed and no emergency buttons are activated.

  6. #6

    Re: Maho MH600E Error 0 23, I 05

    Quote Originally Posted by minisoren View Post
    I tried what you recommended but hydraulic stop when I release the button, and I have the error that is showed on the picture.
    When I tri to start, all the safety gates are closed and no emergency buttons are activated.
    Are your constants ok? Is the table all the way down?

  7. #7
    Member
    Join Date
    Apr 2020
    Posts
    5

    Re: Maho MH600E Error 0 23, I 05

    Constants seems ok, i am able to start and run all 3 axis to reference point.
    Next step spindel RPM and tool changes check:

    If i try to start spindel i get alarm E93. i use S600M3.
    If i try to changes the tool, the tool magazine just keep spinding ( tool magazin is emty) but it should do the opreation anyway? T6M6

  8. #8

    Re: Maho MH600E Error 0 23, I 05

    The Maho mh 600 e has a gearbox for speeds. So you ca only imput fix speeds like S 500 , S630 .

  9. #9
    Member
    Join Date
    Oct 2018
    Posts
    10

    Re: Maho MH600E Error 0 23, I 05

    Hi do you still have this problem?
    There is normally a reference switch on the tool magazine, if this is faulty the magazine cannot reference and position properly
    A t b

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •