523,729 active members*
1,815 visitors online*
Register for free
Login
IndustryArena Forum > Machine Controllers Software and Solutions > Dynomotion/Kflop/Kanalog > is the Dynomotion controll as confusing as it seems?
Page 3 of 3 123
Results 41 to 49 of 49
  1. #41
    Quote Originally Posted by TomKerekes View Post
    Hi Gunmachinist,

    Its not clear you understand you need Motor Drives (Amplifiers) to drive your motors. Do you?

    The first step should be to not use KFLOP/Kanalog at all and test your Amplifiers as described here.

    That sounds mostly wrong. Please don't power up the system until you understand what you are doing or you will likely damage another set of boards.
    Ok, I see im missing a few items. Wasn't aware I needed an amplifier to run the servos. It would probably help if someone started a thread with pictures of varrious setups.

    When it comes to electrical work, I like to draw with crayons and drool on myself.

  2. #42
    Junior Member
    Join Date
    May 2006
    Posts
    3375

    Re: is the Dynomotion controll as confusing as it seems?

    Earlier I asked if you have Motor Drives and Power Supply and you replied "yes". But it seems we miss communicated.

    There are lots of build Threads such as this. So the first step will be for you to figure out if you have Amplifiers or not.
    TK
    http://dynomotion.com

  3. #43
    Quote Originally Posted by TomKerekes View Post
    Earlier I asked if you have Motor Drives and Power Supply and you replied "yes". But it seems we miss communicated.

    There are lots of build Threads such as this. So the first step will be for you to figure out if you have Amplifiers or not.

    Thanks for all the help, I'm just highly electricaly dumb.

  4. #44
    Community Moderator Jim Dawson's Avatar
    Join Date
    Dec 2013
    Posts
    4304

    Re: is the Dynomotion controll as confusing as it seems?

    Quote Originally Posted by Gunmachinist View Post
    Ok, I see im missing a few items. Wasn't aware I needed an amplifier to run the servos. It would probably help if someone started a thread with pictures of varrious setups.

    When it comes to electrical work, I like to draw with crayons and drool on myself.

    Please post a few pictures of your control panel. Maybe we can help.
    Jim Dawson
    Sandy, Oregon, USA

  5. #45
    Quote Originally Posted by Jim Dawson View Post
    Please post a few pictures of your control panel. Maybe we can help.
    Will do, just as soon as I get some servo amplifiers.

  6. #46
    Community Moderator Jim Dawson's Avatar
    Join Date
    Dec 2013
    Posts
    4304

    Re: is the Dynomotion controll as confusing as it seems?

    Quote Originally Posted by Gunmachinist View Post
    Will do, just as soon as I get some servo amplifiers.
    What happened to the original drives (servo amplifiers)?
    Jim Dawson
    Sandy, Oregon, USA

  7. #47
    Quote Originally Posted by Jim Dawson View Post
    What happened to the original drives (servo amplifiers)?
    I assume your talking about the original Anilam system drives. I couldn't get them to work so I scrapped the hole system and started over, I was just a little confused as to what all goes into creating a new system. Oh, well best way to learn is by doing, and doing again..and again.

  8. #48
    Community Moderator Jim Dawson's Avatar
    Join Date
    Dec 2013
    Posts
    4304

    Re: is the Dynomotion controll as confusing as it seems?

    Have you decided on what drives you drives you are going to get?
    Jim Dawson
    Sandy, Oregon, USA

  9. #49
    Quote Originally Posted by Jim Dawson View Post
    Have you decided on what drives you drives you are going to get?

    I found Advanced Motion Controls 12A8K on ebay for cheap, so Im going to give it a shot.

Page 3 of 3 123

Similar Threads

  1. Use co2 laser machine controll card to controll 30W fiber source
    By oneeye in forum Laser Control Software
    Replies: 2
    Last Post: 06-12-2020, 05:23 PM
  2. Confusing breakage
    By tbaker2500 in forum Tormach Personal CNC Mill
    Replies: 2
    Last Post: 09-07-2013, 04:01 AM
  3. Confusing diagram
    By sirevert in forum Stepper Motors / Drives
    Replies: 6
    Last Post: 09-25-2009, 08:57 AM
  4. DATA BIT 8 AND 7 CONFUSING
    By CHANDRU in forum Mazak, Mitsubishi, Mazatrol
    Replies: 0
    Last Post: 05-24-2009, 11:08 AM
  5. BobCad-Cam V21.5 is confusing
    By jessey in forum BobCad-Cam
    Replies: 3
    Last Post: 05-24-2009, 10:43 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •