584,805 active members*
4,987 visitors online*
Register for free
Login
IndustryArena Forum > Machine Controllers Software and Solutions > UCCNC Control Software > High Precision Automatic Tool Sensor Cnc Z Axis, How to wire to UB1 Controller UCCNC
Results 1 to 6 of 6
  1. #1
    Join Date
    Mar 2020
    Posts
    60

    High Precision Automatic Tool Sensor Cnc Z Axis, How to wire to UB1 Controller UCCNC

    hello,


    Looking for help to Setup 4 wire automatic tool sensor to UB1. I seen people on Youtube with it setup on UB1, UCCNC Software. Didn't show how it was setup/connected.

    The only wiring i found was on google.

    Not sure if it apply to this probe, or perhaps they the same.









    Would appreciate all feedback


    thanks

    User avatar
    lloxley016

    Posts: 3
    Joined: Wed Apr 29, 2020 9:12 pm
    Location: orlando

  2. #2
    Join Date
    Mar 2012
    Posts
    34

    Re: High Precision Automatic Tool Sensor Cnc Z Axis, How to wire to UB1 Controller UC

    Hi, gotten this to work ? I use this one quite similar, just with chip blowoff.

  3. #3
    Join Date
    Mar 2020
    Posts
    60

    Smile Re: High Precision Automatic Tool Sensor Cnc Z Axis, How to wire to UB1 Controller UC

    Ok. would share how did you wire it up... draw diagram.

    right now hive mines working, but only the yellow/green on X105 and 0V Pin/5 and I/O Port1, And work perfect. But that it can also be connected E-stop too.
    So when it go to far down, it trigger E-stop and the probing will stop. project your bit....


    I also found other documents from other forum, there they successfully set the up. but didn't show how they wire it. so sad..

    anyway i'll doing my research on this project.

  4. #4
    Join Date
    Mar 2012
    Posts
    34

    Re: High Precision Automatic Tool Sensor Cnc Z Axis, How to wire to UB1 Controller UC

    Hi, what i did is that i just connected the override limit to the pins, and then i have connected that pin to reset in UCCNC, i belive it's code 152 on pin setup

    Sent fra min SM-G975F via Tapatalk

  5. #5
    Join Date
    Mar 2020
    Posts
    60

    Re: High Precision Automatic Tool Sensor Cnc Z Axis, How to wire to UB1 Controller UC

    Hi

    Here is picture of UB1., Can you mark what you are talking about. "" just connected the override limit to the pins, and then i have connected that pin to reset in UCCNC ""


    UB1 doesn't hive reset pin., You talking E-stop











    Thanks
    Attached Thumbnails Attached Thumbnails ub1.jpg  

  6. #6
    Join Date
    Sep 2014
    Posts
    28

    Re: High Precision Automatic Tool Sensor Cnc Z Axis, How to wire to UB1 Controller UC

    Did this configuration work for you?:

    "Yellow wire / => assuming it's ( Probe Single )


    Green Wire /=> assuming it's ( Probe Return Single )


    Red wire /=> 24v + Resistor 2k 1w


    Black wire /=> Either ( COM- ) or ( 0V ) Or Connect Green wire to ( COM-) + resistor"

    Did you connect the overtravel circuit to the OSSD safety circuit on the UB1?

Similar Threads

  1. Replies: 0
    Last Post: 06-24-2020, 09:25 AM
  2. Replies: 1
    Last Post: 01-01-2020, 12:15 AM
  3. Automatic Tool Height Sensor input to KFLOP
    By amitkumar171 in forum Dynomotion/Kflop/Kanalog
    Replies: 9
    Last Post: 04-03-2018, 11:44 PM
  4. How to wire Active High proximity sensor to kflop JP7
    By amitkumar171 in forum Dynomotion/Kflop/Kanalog
    Replies: 17
    Last Post: 02-19-2018, 05:55 PM
  5. High precision 4 and 5 axis shop.
    By Vsmfg in forum RFQ (Request for Quote)
    Replies: 0
    Last Post: 04-27-2011, 10:31 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •