584,861 active members*
4,929 visitors online*
Register for free
Login
Results 1 to 5 of 5
  1. #1
    Join Date
    Nov 2015
    Posts
    8

    Stepper Amperage

    I am retrofitting a mill and the old steppers just aren't working well on all three axis so I am replacing them and the drivers as well. I am planning on keeping the power supply, but I want to make sure I don't get to high Amperage steppers.

    The power supply is a 48volt toroidal power supply. It has wires running to each stepper and each of those three circuits has a 2 Amp Fuse on it. Does that mean I can use the 2/3 rule and use 3 Amps steppers? Or am I limited to 2 Amp steppers, because of the fuses?

  2. #2
    Join Date
    Jul 2018
    Posts
    6254

    Re: Stepper Amperage

    If you get "higher" amperage steppers they will work, just at the set amperage of the driver. Maybe the steppers are fine and you need to adjust the driver settings or the controller settings (or its a mechanical issue with the machine. tight bearings, alignment etc). I'd work through the system before replacing anything and track down the exact cause of the issue. What do you mean by "not working well" steppers either work or don't work? usually.. Peter

  3. #3
    Join Date
    Mar 2003
    Posts
    35538

    Re: Stepper Amperage

    What's the current rating on the power supply?
    I'd get rid of the fuses, and get 5 or 6 amp steppers. Typically, the higher the current, the better the performance. 2-3 amp steppers are on the lower end for power and speed.
    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)

  4. #4
    Join Date
    May 2006
    Posts
    4043

    Re: Stepper Amperage

    Note that the average current from a supply is usually much lower than the stepper current. For example a 2.4V 5A motor will only draw about 0.25A from a 48V supply when stopped due to conservation of energy. Both are 12Watts. As the motor moves under load the motor will provide mechanical power and draw more current from the supply.
    TK
    http://dynomotion.com

  5. #5
    Join Date
    Nov 2015
    Posts
    8

    Re: Stepper Amperage

    Its definitely the steppers that are bad. When I test it the X axis works fine. The Z axis didn't move at all I removed the stepper and it was spinning only intermittently when I test it. The Y axis works fine going down but going up it skips and makes noise. All three of the drivers seem to be working though since I tested them on the X axis.

    The transformer is made by Talema its about 110mm x 60mm I cant find the model number on their site and it doesn't have any specification other then that on the side. It might be similar to one of these.

    https://talema.com/wp-content/upload...ary-0225VA.pdf

    https://talema.com/wp-content/upload...ary-0300VA.pdf

    Click image for larger version. 

Name:	IMG_1039.jpg 
Views:	2 
Size:	93.1 KB 
ID:	451443Click image for larger version. 

Name:	IMG_1023.jpg 
Views:	3 
Size:	91.7 KB 
ID:	451445Click image for larger version. 

Name:	IMG_1042.jpg 
Views:	2 
Size:	95.0 KB 
ID:	451447Click image for larger version. 

Name:	IMG_1043.jpg 
Views:	3 
Size:	93.0 KB 
ID:	451449

    The mill is a LabVolt 5600. The capacitor is a mallory.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •