548,545 active members*
2,398 visitors online*
Register for free
Login
Results 1 to 13 of 13
  1. #1

    Join Date
    Nov 2021
    Posts
    11

    VFS5 NOT READY

    When the drives are turned on, the LED on the VFS5 flashes 5 times. + - 18 volts available 10 volts available.
    MOTION LINK IN TERMINAL ERROR 83 AND 84
    1.Sabre1000 machine

    2. No wiring diagrams!

  2. #2
    Registered
    Join Date
    Mar 2011
    Posts
    390

    Re: VFS5 NOT READY

    1) if I'm remembering correctly, error 83 and 84 are typical of what I see when someone unfamiliar with Motionlink uses it and enters invalid commands so they may not be related to your issue. It is also normal to see err 14 power bus and drive powered up messages, but since it only stores the most recent codes, these may have been pushed off the list.

    2) You can get the wiring diagrams from Fives, they will want the diagram number on the serial number plate. These won't likely help much with the current VFS5 issue, but it is always better to have them when working on a machine.

  3. #3

    Join Date
    Nov 2021
    Posts
    11

    Re: VFS5 NOT READY

    Can anyone help with the wiring diagram?
    My electrical cabinet number
    91203230
    Thank you!

  4. #4

    Join Date
    Nov 2021
    Posts
    11

    Re: VFS5 NOT READY

    Our fan crashed on VFS5.
    vfs5 monitors the presence of a fan?
    Is it possible temporarily without a fan?

  5. #5
    Registered
    Join Date
    Dec 2006
    Posts
    544

    Re: VFS5 NOT READY

    When the light flashes it is because of a bad battery, contact kilroy corporation , kilroycorp.com ???

    Mike CNC Machine Services INC | Cincinnati Milacron MachinesCNC Machine Services

  6. #6

    Join Date
    Nov 2021
    Posts
    11

    Re: VFS5 NOT READY

    The LED is not blinking now.
    When all voltages are switched on:
    + 10v
    + -18v
    + 24v on c2 pin 6.9
    jumper on S7 MOTION, LIMIT
    And on PSR4 / 5
    Shines:
    sys ok
    Cpu
    FAULT
    RELAY
    AKTIV NO!
    I checked the resolver with 18om, 18om, and 36om
    On TERMINAL (Motion Link) when you enter EN (ON), appears
    ERROR 83 ...
    AND ALL

    What else can I check?

  7. #7

    Join Date
    Nov 2021
    Posts
    11

    Re: VFS5 NOT READY

    now shines when voltage is applied
    ACTIV
    CPU blinking unpleasantly
    How to do autoload correctly?

  8. #8

    Join Date
    Nov 2021
    Posts
    11

    Re: VFS5 NOT READY

    CPU blinks continuously

  9. #9

    Join Date
    Nov 2021
    Posts
    11

    Re: VFS5 NOT READY

    ??? ????????? ?????????????

  10. #10

    Join Date
    Nov 2021
    Posts
    11

    Re: VFS5 NOT READY

    It is now detected when the voltage is switched on
    ERROR 27 ”R / D JUMPERS” SEVERITY 3

    Either the jumpers on your BDS5 MC2 card are incorrectly set or the wrong
    TL has been loaded. Contact the factory.
    What to do with it?

  11. #11

    Join Date
    Nov 2021
    Posts
    11

    Re: VFS5 NOT READY

    Who has a TL file on VFS5?

  12. #12

    Join Date
    Nov 2021
    Posts
    11

    Re: VFS5 NOT READY

    There are instructions for creating a VFS5 spindle drive configuration?
    Or is MOTION LINK + enough !?
    Who can I ask questions?

  13. #13

    Join Date
    Nov 2021
    Posts
    11

    Re: VFS5 NOT READY

    Does the forum work or not?

Similar Threads

  1. VFS5 Kollmorgen drive
    By juniormachinist in forum Cincinnati CNC
    Replies: 10
    Last Post: 11-28-2018, 07:24 PM
  2. Koolmorgen VFS5 questions
    By bertcnc in forum Cincinnati CNC
    Replies: 1
    Last Post: 09-28-2016, 05:16 PM
  3. VFS5 FAN
    By Muggins in forum Cincinnati CNC
    Replies: 8
    Last Post: 05-02-2016, 06:26 PM
  4. VFS5 software
    By jacquestek in forum Cincinnati CNC
    Replies: 3
    Last Post: 10-05-2011, 01:57 PM
  5. Please help me. VFS5
    By udom in forum Cincinnati CNC
    Replies: 13
    Last Post: 06-21-2011, 08:26 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •