[steer]

Purchased another used Hardinge, same control as another we have. Noticed on position page it has a working parts counter and cycle time. Anyone know how to zero out the parts counter? Don't tell me it's a parameter. Hardinge tells me there is an entire page for just the counter, I can select the number of pieces and the machine will stop cycling? Can't find anything to that effect.

[M-man]

I think you got to go offsetkey a couple of times and when you get to the PWE screen, press arrow down 1-2 times and you will get the part required and machined parts pages. MUst be in MDi to set new numbers here.

[viorel26]

Purchased another used Hardinge, same control as another we have. Noticed on position page it has a working parts counter and cycle time. Anyone know how to zero out the parts counter? Don't tell me it's a parameter. Hardinge tells me there is an entire page for just the counter, I can select the number of pieces and the machine will stop cycling? Can't find anything to that effect.

To zero out the parts counter (on position page) press "P" and then press "Can"
To zero out cycle time(Run Time) on position page press "R" and then press"Can"

[steer]

Pressing "P" then "CAN" works like a charm, thanks.
Couldn't get to the PWE page by hitting offset button. Hardinge tek said the same thing, maybe I'm doing something wrong but I don't see the PWE page.

[viorel26]

I think you got to go offsetkey a couple of times and when you get to the PWE screen, press arrow down 1-2 times and you will get the part required and machined parts pages. MUst be in MDi to set new numbers here.

Yes for Fanuc 21,18

But on Fanuc O-T for enable PWE press "Param/Diag" and with "Page up" or "Page Dw." go to SETING 2 screen (in MDI mode) and set PWE to 1
Prameter no.600 is to set Number of Required Parts

[steer]

Works great, thanks. no need to go to parameter 600, can change it right on the PWE page.

[steer]

Is a big deal to turn this feature ON in my other machine?

[viorel26]

Param. 907 bit 4 for run time and parts count display.

[steer]

parameter 907 on machine with parts counter read "01011010" on the other machine with no counter it reads "01001000" , so 2 bits are changed?
It's been awhile, also forgot how to enable PWE to change paramter.

[viorel26]

parameter 907 on machine with parts counter read "01011010" on the other machine with no counter it reads "01001000" , so 2 bits are changed?
It's been awhile, also forgot how to enable PWE to change paramter.

No
On Fanuc O-T for enable PWE press "Param/Diag" and with "Page up" or "Page Dw." go to SETING 2 screen (in MDI mode) and set PWE to 1
param. 907 bit #7 #6 #5 #4 #3 #2 #1 #0
bit#4 For Run Time and Parts Count Display set param 907 bit 4 to 1
bit#1 is for 2nd Aux. function

[steer]

Works great! Seems like it's always been working, just not displayed. Parts counter was at 480,380.
What do you think the aux. function is?

[mbracement]

I think you got to go offsetkey a couple of times and when you get to the PWE screen, press arrow down 1-2 times and you will get the part required and machined parts pages. MUst be in MDi to set new numbers here.

This did the trick for me, had to be in MDI mode. Thanks!

[Edwin Murch]

Steer,
My X axis died and can't read the ac motor numbers can you help ?
CHNC I OT control
wiring diagram A13B-0139-8540
GEF OTB
CN-3085-T

Thanks in advance
Edwin Murch
[email protected]

[Uky]

Pdf on ot parameter

[zavateandu]

No
On Fanuc O-T for enable PWE press "Param/Diag" and with "Page up" or "Page Dw." go to SETING 2 screen (in MDI mode) and set PWE to 1
param. 907 bit #7 #6 #5 #4 #3 #2 #1 #0
bit#4 For Run Time and Parts Count Display set param 907 bit 4 to 1
bit#1 is for 2nd Aux. function

Domnule Viorel
daca nu stiati va amintesc eu ca indicarea parametrilor speciali ca de exemplu 907.4 catre terte persoane se face doar in privat si nu public
daca continuati veti fi inlaturat din forum
adaca doriti sa ajutati pe cineva cu modificarea parametrilor speciali din seria 900 la orice controller, va rog sa o faceti privat.
Sper ca ati inteles.
Numai bine

@Everyone
If you want to help somebody by modifying the special paameters from 900 series to any controller ,please do it privatly with the user you help
Do not post this public as you will be removed from forum.
Thank you.

[mohsene_e]

Hi everybody
I need help for fanuc o-t. we purchased a lathe with fanuc o-t controller but there is no document with machine. If any body has any documents please send me.
my email: [email protected]
Thanks.