584,829 active members*
4,868 visitors online*
Register for free
Login
IndustryArena Forum > CNC Electronics > CNC Machine Related Electronics > I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle
Page 1 of 3 123
Results 1 to 20 of 42
  1. #1
    Join Date
    May 2016
    Posts
    27

    I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    It is rated for 24,000 rpm. I cannot achieve more 7,999 rpm any suggestions?
    Any Help is appreciated

    When running HZ registers 133.33 It is set to 400 hz 1.7 Amps
    Last edited by mpresti8; 02-21-2023 at 05:35 PM.

  2. #2
    Join Date
    Jan 2005
    Posts
    15362

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by mpresti8 View Post
    It is rated for 24,000 rpm. I cannot achieve more 7,999 rpm any suggestions?
    Any Help is appreciated

    When running HZ registers 133.33 It is set to 400 hz 1.7 Amps
    1.7Ax3=5.1A at the spindle 8.8A at the supply.

    You did not say what spindle you have; it sounds like your Parameters are not set correctly.

    How many Amps is your AC supply??
    Mactec54

  3. #3
    Join Date
    May 2016
    Posts
    27

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    20 Amp circut
    This unit was running at Max revolution until this happened

  4. #4
    Join Date
    May 2016
    Posts
    27

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    I have the GDZ-80-1.5B 24000 rpm 1.5 KW 110V 400Hz 5ASpindle water cooled

  5. #5
    Join Date
    Jan 2005
    Posts
    15362

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by mpresti8 View Post
    20 Amp circut
    This unit was running at Max revolution until this happened
    Until what happened, did it overload or stall, is this being used from the KeyPad or by remote 0-10v??
    Mactec54

  6. #6
    Join Date
    May 2016
    Posts
    27

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Run by the keypad on the front of the inverter no problems other than I wanted to slow it down because I believe it was running too fast for the surfacing blade i had on it. I was checking settings and the VI VR pin that you move the jumper on to change from the keypad operation to the Mach 3 software operation That is when i could not get it to work properly at this time it is shorted across the VR pins

  7. #7

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Did you check if this Parameter PD144: Max Motor RPM is set to 3000

    https://www.automationtechnologiesin...5-110vac-input

  8. #8
    Join Date
    May 2016
    Posts
    27

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    let me check that real fast

    PD144 = 3000

  9. #9
    Join Date
    May 2016
    Posts
    27

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    PD144 = 3000


  10. #10
    Join Date
    May 2016
    Posts
    27

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by automationtechinc View Post
    Did you check if this Parameter PD144: Max Motor RPM is set to 3000

    https://www.automationtechnologiesin...5-110vac-input
    PD144 is set to 3000

  11. #11
    Join Date
    Jan 2005
    Posts
    15362

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by mpresti8 View Post
    let me check that real fast

    PD144 = 3000
    This Parameter PD144 is related to the Max RPM only.

    This is the Parameters you need for KeyPad / Pot use.

    Pot Control
    PD001=0

    PD002=1

    PD070=1

    JI Jumper 2-3=VI Position. You can try either position as some of these drives can be either for Pot use, these Parameters are important as well to make it run also for Pot control
    Mactec54

  12. #12
    Join Date
    May 2016
    Posts
    27

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by mactec54 View Post
    This Parameter PD144 is related to the Max RPM only.

    This is the Parameters you need for KeyPad / Pot use.

    Pot Control
    PD001=0

    PD002=1

    PD070=1

    JI Jumper 2-3=VI Position. You can try either position as some of these drives can be either for Pot use, these Parameters are important as well to make it run also for Pot control
    Those settings are correct still no luck

  13. #13
    Join Date
    Jan 2005
    Posts
    15362

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by mpresti8 View Post
    Those settings are correct still no luck
    Check the Jumper is not damaged.

    What are the Parameters you have set in the Drive
    Mactec54

  14. #14
    Join Date
    May 2016
    Posts
    27

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by mactec54 View Post
    Check the Jumper is not damaged.

    What are the Parameters you have set in the Drive
    Curent settings are as follows

    PD001=0
    PD002=0
    PD003=400
    PD005=400
    PD004=400
    PD007=.0.50
    PD009=15
    PD010=8
    PD011=133.33
    PD013=8 FACTORY RESET
    PD014=10
    PD015=10
    PD025=1
    PD027=0.80
    PD141=110
    PD142=5
    PD143=2
    PD144=3000

    Jumper is fine

    Last edited by mpresti8; 02-23-2023 at 07:10 PM.

  15. #15
    Join Date
    Jan 2005
    Posts
    15362

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by mpresti8 View Post
    Curent settings are as follows

    PD001=0
    PD002=0
    PD003=400
    PD005=400
    PD004=400
    PD007=.0.50
    PD009=15
    PD010=8
    PD011=133.33
    PD013=8 FACTORY RESET
    PD014=10
    PD015=10
    PD025=1
    PD027=0.80
    PD141=110
    PD142=5
    PD143=2
    PD144=3000

    Jumper is fine

    PD002=1 this needs to be 1 not 0

    PD070=1 also for the Pot to work

    PD007=20

    PD025=0 Default

    PD027=10 this is normally left at the default, if you want to use it than it should be set at the max of 10

    You also may need these 2 Parameters set also

    PD072=400

    PD073=133 Your Minimum Speed
    Mactec54

  16. #16
    Join Date
    May 2016
    Posts
    27

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by mactec54 View Post
    PD002=1 this needs to be 1 not 0

    PD070=1 also for the Pot to work

    PD007=20

    PD025=0 Default

    PD027=10 this is normally left at the default, if you want to use it than it should be set at the max of 10

    You also may need these 2 Parameters set also

    PD072=400

    PD073=133 Your Minimum Speed
    i made those inputs and still max rpm is7999 I think this thing is haunted
    Last edited by mpresti8; 02-23-2023 at 09:22 PM.

  17. #17
    Join Date
    Jan 2005
    Posts
    15362

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by mpresti8 View Post
    i made those inputs and still max rpm is7999 I think this thing is haunted
    There is another Parameter that is not set correct then, as that is sitting at your minimum speed setting, is there any others that you may have changed.
    Mactec54

  18. #18
    Join Date
    Jan 2005
    Posts
    15362

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by mactec54 View Post
    There is another Parameter that is not set correct then, as that is sitting at your minimum speed setting, is there any others that you may have changed.
    Are you trying to run from the KeyPad or from Mach3 if from Mach3 then you need a 0-10v Analog output from the Breakout Board, for this to work, if still only working from the KeyPad do the Arrow keys up /down change the speed.

    What Breakout Board are you using.
    Mactec54

  19. #19
    Join Date
    May 2016
    Posts
    27

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    I am running from the VFD not the computer or Mach 3

    Honestly this thing is driving me nuts.. One thing that I have seen on these YouTube videos is that when they change a value and press set the screen displays END mine does not display that

  20. #20

    Re: I have a huanyang hy02d211b VFD . 110 VAC water cooled spindle

    Quote Originally Posted by mpresti8 View Post
    I am running from the VFD not the computer or Mach 3

    Honestly this thing is driving me nuts.. One thing that I have seen on these YouTube videos is that when they change a value and press set the screen displays END mine does not display that
    Give me a call, I will help you to check to find the problem

    The phone number is on our website:

    https://www.automationtechnologiesin...ucts-page/vfds

Page 1 of 3 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •