[MetalMolder]

I just started at this company it is my first experience with Fadal.
after I drill a clearance hole with the endmill I want to go back in and pocket the area. After the drill routine my program jumps back to the beginning of the tool. Anyone that can tell me why would be greatly appreciated.
My previouse experience is with Matsuura and Robo Drills.

N3T1M6
N4G0G90G54X-.3175Y-4.625S8000M3
N5G43H1Z1.
Z.1M8
N6G1G41D51Z-1.1F300.
N7Y-4.125F100.
N8Y0.
N9Y.5
N10G0Z.1
G40
N11X40.8175
N12G1G41D51Z-1.1F300.
N13Y0.F100.
N14Y-4.125
N15Y-4.625
N16G0Z.1
G40
N17X1.6625Y.3875
N18G1Z-.25F300.
N19X18.2175F100.
N20Y-2.255
N21G2X17.78Y-2.6925I-.4375
N22G1X2.1
N23G2X1.6625Y-2.255J.4375
N24G1Y.3875
N25X2.1312Y-.0813
N26X17.7487
N27Y-2.2238
N28X2.1312
N29Y-.0813
N30X2.6Y-.55
N31X17.28
N32Y-1.755
N33X2.6
N34Y-.55
N35X3.0687Y-1.0188
N36X16.8112
N37Y-1.2863
N38X3.0687
N39Y-1.0188
N40G0Z-.15
N41Z.1
N42X21.1525Y.3875
N43G1Z-.25F300.
N44X38.2275F100.
N45Y-2.255
N46G2X37.79Y-2.6925I-.4375
N47G1X21.59
N48G2X21.1525Y-2.255J.4375
N49G1Y.3875
N50X21.6212Y-.0813
N51X37.7587
N52Y-2.2238
N53X21.6212
N54Y-.0813
N55X22.09Y-.55
N56X37.29
N57Y-1.755
N58X22.09
N59Y-.55
N60X22.5587Y-1.0188
N61X36.8212
N62Y-1.2863
N63X22.5587
N64Y-1.0188
N65G0Z.1
N66X5.175Y-1.755
N6G98G83X5.175Y-1.755Z-1.1R.1Q.05F20.
N7G80
N8G1Z-.55F300.
N9X2.4537Y-1.6088F75.
N10Y-1.9013
N11X7.8962
N12Y-1.6088
N13X2.4537
N14X2.2975Y-1.4525
N15Y-2.0575
N16X8.0525
N17Y-1.4525
N18X2.2975
N19X1.985Y-1.2545
N20Y-2.2557
N21G3X2.1Y-2.37I.115J.0007
N22G1X8.25
N23G3X8.365Y-2.255J.115
N24G1Y-1.255
N25G3X8.25Y-1.14I-.115
N26G1X2.1
N27G3X1.985Y-1.2545J-.115
N28G1X1.6725Y-1.254

[HuFlungDung]

What is your line numbering convention in that program? I don't think it is legal syntax to use identical line numbers.

[MetalMolder]

In the past I have never had the line numbering make a differance. These Fadal machines seem to be a lot more uncooperative than Fanuc based machines. I will try renumbering and see if this helps, but I have to say the logic makes no sense to me. A line number is only a line number. The control should have to see a subroutine callout to jump to another part of the program.

[Delw]

numbering doesnt make a difference until you run canned cycles, like above. fix the numbers and you will be fine.