[visu]

Hello Everybody,

I am Visu, a new member of the CNCzone forum.
I need help with Fanuc OMA control
I bought a Leadwell VMC with Fanuc OMA control. I am able to send and recieve fixed memory part programs from PC to CNC and vice-versa. I am unable to operate the drip feed mode
G127.5 is not listed in the ladder logic and there is no switch for tape mode.
Is it possible to enable the drip feed mode by altering the PMC

Thanks for any help

[offroadxx]

As far as I know, you cannot drip feed an OM-A control. I have the same control and asked the same thing 5 years ago and was told it was not capable of drip feeding without spending a huge amount of money for an upgrade. My .02.

[Dan Fritz]

The 0M-A will not drip-feed. When Fanuc introduced the 0M-B, they added a bit on the I/O interface called "DNCI". If the machine tool builder puts some logic in the ladder to turn on the DNCI bit, then you're able to run in drip-feed mode. The 0M-A never had this bit, so there's no chance of making it work, even if you can edit the ladder.

If you had a 0M-B or 0M-C without a TAPE mode on the mode select switch, it would be possible to add the function by editing the ladder.

[Jung]

Hello Everybody,

I am Visu, a new member of the CNCzone forum.
I need help with Fanuc OMA control
I bought a Leadwell VMC with Fanuc OMA control. I am able to send and recieve fixed memory part programs from PC to CNC and vice-versa. I am unable to operate the drip feed mode
G127.5 is not listed in the ladder logic and there is no switch for tape mode.
Is it possible to enable the drip feed mode by altering the PMC

Thanks for any help

I can help you turn on DNC on OMA controller. PM me.

[guhl]

The 0M-A will not drip-feed. When Fanuc introduced the 0M-B, they added a bit on the I/O interface called "DNCI". If the machine tool builder puts some logic in the ladder to turn on the DNCI bit, then you're able to run in drip-feed mode. The 0M-A never had this bit, so there's no chance of making it work, even if you can edit the ladder.

If you had a 0M-B or 0M-C without a TAPE mode on the mode select switch, it would be possible to add the function by editing the ladder.

on my Fanuc 0MA with analog servo drip feed works fine without any additional option
software version 402

[brightmachinery]

Hello
I have recently bought Leadwell VMC with OM-A and i wanted it to accept Drip feeding /DNC can any one help?


best regards
Bilal

[guhl]

Hello
I have recently bought Leadwell VMC with OM-A and i wanted it to accept Drip feeding /DNC can any one help?
best regards
Bilal

look at your ladder and find what signal turns G127.5 (DNCI signal) on

[cmpcleveland]

look at your ladder and find what signal turns G127.5 (DNCI signal) on

My machine doesn't appear to have a "ladder" only parameters page and diagnostic page. Is there a function to unlock the "ladder" page?

[Jung]

Hi cmpcleveland, What is the fanuc control model?
check the line#127 of diagnostic screen, bit #5 if it is 1.

[sehmbi2000]

dear sir
i have fanuc 0ma control it dos not show g127.5 want to editing in ladder can i send you copy of e-prom
mukesh dhiman
e-mail [email protected]
+9109814042108

[sehmbi2000]

Hello Everybody,

I am mukesh, a new member of the CNCzone forum.
I need help with Fanuc OMA control
I bought a johnford VMC with Fanuc OMA control. I am able to send and recieve fixed memory part programs from PC to CNC and vice-versa. I am unable to operate the drip feed mode
G127.5 is not listed in the ladder logic and there is no switch for tape mode.
Is it possible to enable the drip feed mode by altering the PMC

Thanks for any help
[email protected]

[sehmbi2000]

Hi cmpcleveland, What is the fanuc control model?
check the line#127 of diagnostic screen, bit #5 if it is 1.

Hello Everybody,

I am mukesh, a new member of the CNCzone forum.
I need help with Fanuc OMA control
I bought a johnford VMC with Fanuc OMA control. I am able to send and recieve fixed memory part programs from PC to CNC and vice-versa. I am unable to operate the drip feed mode
G127.5 is not listed in the ladder logic and there is no switch for tape mode.
Is it possible to enable the drip feed mode by altering the PMC

Thanks for any help
[email protected]
show G127.5 show this 00000100

[toranacar]

Interesting thread, I have a Leadwell MCV OP Fanuc OM. The manual I have says OMF

[lucamurino]

Hello please can you help me to enable drip feed on my Fanuc 0ma?
Thankyou

[lucamurino]

on my Fanuc 0MA with analog servo drip feed works fine without any additional option
software version 402

Please can you help me with that?